BYD Shark 6 Canopy & Tub Setup Guide

The BYD Shark 6 is the ute that threw a curveball at every canopy fitter, auto electrician and weekend touring…

By Chris 44 min read Published Last updated:

BYD Shark 6 Canopy & Tub Setup Guide
Table of contents

The BYD Shark 6 is the ute that threw a curveball at every canopy fitter, auto electrician and weekend touring planner in the country. It looks like a dual cab. It works like a dual cab. But under the skin, it is a plug in hybrid with a big battery, independent rear suspension, a kerb weight north of 2,700 kg and 230 V power outlets in the tub.

That changes the canopy conversation. Payload is tighter than most diesel utes. Roof load limits are lower than many owners expect. And the built in V2L power means your camping or worksite electrical setup can be simpler or more complicated, depending on how you approach it.

The 2026 range now spans three variants: the Dynamic Cab Chassis, the Premium pickup and the Performance pickup. The Performance closes the towing gap to 3,500 kg and adds a new Crawl Mode, but trades 65 kg of payload for the bigger powertrain. Both pickups share the same tub, so every canopy that fits one fits the other.

This guide covers the stuff that actually matters before you spend a dollar: tub dimensions, payload maths, canopy types, mounting options, electrics, storage layouts, roof loads, towing interactions, dust sealing, legal basics and three complete build packages you can hand to a fitter. No fluff, just practical info for tradies, tourers and everyone in between.

 

Quick Shark 6 spec box (canopy relevant numbers)

Spec Premium Performance
Tub length 1,520 mm 1,520 mm (same tub)
Tub width 1,500 mm (1,224 mm between arches) 1,500 mm (1,224 mm between arches)
Tub depth 517 mm 517 mm
Tray volume 1,200 L 1,200 L
Kerb weight 2,710 kg 2,775 kg
GVM 3,500 kg 3,500 kg
Payload (standard) ~790 kg ~725 kg
Payload (GVM upgraded) ~1,140 kg* Confirm with Ironman
Cab roof load 75 kg dynamic / ~300 kg static 75 kg dynamic / ~300 kg static
Max braked towing 2,500 kg 3,500 kg
Max unbraked towing 750 kg 750 kg
Max towball load 250 kg 350 kg
Tub power (V2L) 230 V cargo socket 230 V cargo socket
GCM 5,750 kg 6,650 kg
Wading depth 700 mm 700 mm
Ground clearance 230 mm 230 mm
Crawl Mode Coming via OTA update Standard

*Ironman 4×4 GVM upgrade currently listed for the Premium configuration. Confirm Performance variant compatibility before ordering.

Which Shark 6 are you building?

The 2026 range expanded from one variant to three. The canopy conversation is different for each.

Premium pickup ($57,900)

The Premium carries the 1.5 litre PHEV powertrain with 321 kW and 650 Nm. It tows 2,500 kg braked with a 250 kg towball limit and a 5,750 kg GCM. Payload is approximately 790 kg. This is the better starting point for a heavily accessorised canopy build because it has 65 kg more payload than the Performance.

Performance pickup ($62,900)

The Performance swaps to a 2.0 litre turbo with an upgraded 200 kW front motor, producing 350 kW and 700 Nm combined. It tows 3,500 kg braked with a 350 kg towball limit and a 6,650 kg GCM. Payload drops to approximately 725 kg due to the heavier powertrain (2,775 kg kerb). The Performance also introduces Crawl Mode, which limits speed to 20 km/h and continuously adjusts torque for improved off road traction on steep, slippery or rocky terrain.

Both pickups share the same tub dimensions (1,520 x 1,500 x 517 mm) and the same 1,200 L volume. Any canopy designed for the Shark 6 pickup fits both variants.

Dynamic Cab Chassis ($55,900)

The Dynamic uses the Premium’s 1.5 litre powertrain but has no factory tub. It requires a separately fitted tray or service body. The optional Ironman 4×4 alloy tray weighs approximately 150 kg and reduces payload to around 750 kg. This guide covers the pickup tub. Dynamic Cab Chassis owners need a tray specific build approach.

Before you buy anything: the three point check

Before you order a canopy, a rack, a drawer system or even a fridge slide, answer these three questions:

  1. Weight: What is your actual remaining payload after passengers, the canopy itself and any towball load? If you are under 200 kg of headroom, stop and reconsider your build list or look at a GVM upgrade first.
  2. Fitment: Have you measured your tub with the factory liner in place? The Shark 6 comes with a spray in bedliner from the factory and it changes the usable width at the tub lip. Do not assume catalogue dimensions match your ute exactly. The BYD Shark 6 tub dimensions guide covers the measurement process in detail.
  3. Power: Are you planning to run accessories off V2L (the 230 V outlets), off a separate 12 V system or both? This decision shapes your entire electrical layout and determines whether you need a secondary battery or not.

Get those three sorted and the rest of the build falls into place.

Quick answer: what canopy setup works best for most Shark 6 owners?

Not everyone wants to read 10,000 words. Fair enough. Here are three paths that cover the majority of Shark 6 builds we see.

Path 1: Tradie security build

You need your tools locked up, visible internal lighting and fast access on site. You do not need a fridge or a rooftop tent. The BYD Shark 6 tradie canopy build guide covers the full tradie build in detail, including zone layouts, shelving, V2L worksite power and five trade specific examples.

  • Aluminium canopy with gullwing side windows or solid panels
  • Central locking tied to the vehicle or keyed alike
  • LED strip lighting inside the canopy
  • Drawer system or shelving to organise power tools, fasteners and consumables
  • No roof rack or a basic set of crossbars for the odd length of conduit or ladder
  • V2L for charging batteries and running small power tools on site
  • Estimated canopy + fitout weight: 120 to 180 kg

Path 2: Touring and camping build

You want a sealed canopy that keeps dust out, a fridge running 24/7, water storage, an awning and possibly a rooftop tent. The BYD Shark 6 touring build guide covers the full touring build including power strategy, water, sleep systems and three packaged recommendations.

  • Aluminium canopy with sliding or lift up side windows for ventilation
  • Fridge slide with a 40 to 60 L compressor fridge
  • Drawer system underneath the fridge platform
  • 100 Ah lithium battery with DC DC charger (or rely on V2L for shorter trips)
  • 2 x 20 L water storage or a compact under tray tank
  • Awning mounted to the canopy side rail
  • Optional rooftop tent on the canopy roof (check weight budget carefully)
  • Estimated canopy + fitout weight: 180 to 300 kg

Path 3: Weekend all rounder

You use the ute for work during the week and want the tub usable for hardware runs, tip runs and the occasional camping weekend. A full canopy feels like overkill.

  • Hard lid (aluminium, rated for crossbar mounting) or electric roller shutter
  • Tub organiser or single drawer unit for basic gear
  • Crossbars on the hard lid or cab roof for bikes, boards or a small cargo basket
  • V2L handles any weekend power needs without extra batteries
  • Estimated lid + accessories weight: 50 to 90 kg

Mini decision tree

  • Need to lock up expensive tools every day? Full canopy (Path 1 or Path 2).
  • Need dustproofing for long dirt roads? Full canopy with positive pressure vent.
  • Need a fridge running overnight? Touring build with battery or V2L if the vehicle is nearby and you are happy using the Shark’s battery.
  • Need a rooftop tent? Canopy mount or tub rack, but do your payload maths first.
  • Need the tub clear for bulky loads most weeks? Hard lid or roller shutter (Path 3).
  • Travelling with a dog? Canopy with ventilation windows and airflow path. Never a sealed roller shutter.

Shark 6 tub + load limits that decide everything (read this first)

This is the section most people skip and then regret later. The Shark 6’s tub and weight numbers are genuinely different from a HiLux or Ranger and understanding them early saves you from buying gear you cannot legally carry.

Tub dimensions and what they mean for canopy fitment

BYD publishes the following tub measurements: 1,520 mm long, 1,500 mm wide at the top and 517 mm deep. Between the rear wheel arches, the floor width narrows to approximately 1,224 mm. That inner width is wide enough for both Australian standard pallets (1,165 x 1,165 mm) and Euro pallets (1,200 x 800 mm), which is a genuine plus for tradies.

The tub volume is listed at 1,200 litres, which is on par with a Ford Ranger Wildtrak and slightly larger than some HiLux tubs.

Before you order a canopy, measure these yourself:

  • Tub lip width (outer): This is where clamp on canopies grip. The factory spray in liner adds material to the lip and can reduce effective width by a few millimetres.
  • Tailgate gap: Measure the distance between the canopy rear edge and the tailgate when closed. A poor gap means water pooling and dust ingress.
  • Inner tie down locations: The Shark 6 has six tie down points, but the ones on the sidewalls (front and centre) sit higher than ideal for low profile loads. Know where they are before your fitter drills any new mounting holes.
  • Tub liner thickness at the lip: The spray in liner can vary slightly. If your canopy is clamp on, this tolerance matters for seal compression.

Common mistake: Ordering a canopy based on published tub dimensions without accounting for the factory liner thickness at the mounting rail. Even 2 to 3 mm can affect clamp pressure and water sealing.

Payload maths (and why Shark 6 owners need to be extra deliberate)

Here is the basic formula:

Available payload = GVM minus Kerb weight

For the Premium: 3,500 kg minus 2,710 kg = approximately 790 kg. For the Performance: 3,500 kg minus 2,775 kg = approximately 725 kg.

That payload has to cover everything that was not on the vehicle when it was weighed at the factory. That means the driver and passengers (budget 75 to 100 kg per person), canopy (60 to 120 kg depending on material and design), drawers (30 to 60 kg), fridge and contents (25 to 40 kg), roof rack or platform (15 to 25 kg), awning (15 to 25 kg), water (20 L = 20 kg), tools, recovery gear, camping kit and towball download (up to 250 kg on the Premium, up to 350 kg on the Performance).

Let us work through a realistic tradie example on the Premium:

Item Weight (kg)
Driver 90
Aluminium canopy 85
Drawer system 40
Tools and consumables in drawers 80
Roof rack + crossbars 18
LED light bar 5
Total 318 kg

That leaves 472 kg of remaining payload, which is still comfortable. But add a passenger (90 kg) and some materials in the tub (150 kg) and you are at 558 kg used with 232 kg left. Start towing a trailer with a 200 kg ball weight and you are at 758 kg, just 32 kg under the limit with nothing else on board.

On the Performance, those same numbers leave only 407 kg after the 318 kg build and the same towing scenario hits 693 kg used with just 32 kg margin and no passenger counted.

This is why the Shark 6 community talks about “weight discipline” constantly. It is not optional. The BYD Shark 6 payload and GVM guide covers the full weight calculation with worked examples and a fill in payload worksheet.

The fix: If you are building a heavy touring setup or a loaded tradie rig, seriously consider the Ironman 4×4 GVM upgrade. It lifts GVM to 3,850 kg and payload to approximately 1,140 kg on the listed Premium configuration. That is an extra 350 kg of legal headroom. The kit includes IM2.5 monotube shocks, matched springs, upgraded axle capacities (front to 1,800 kg, rear to 2,150 kg) and approximately 30 mm of lift. Kits are priced from $3,490 (Medium), $3,590 (Heavy) and $3,690 (Extra Heavy). The upgrade is available for both pre registration and already registered vehicles. The process must comply with VSB 14, the national code of practice for light vehicle modifications (published by the Department of Infrastructure, Transport, Regional Development, Communications and the Arts). The BYD Shark 6 GVM upgrade guide covers kit selection, pricing, state approval pathways and what the upgrade does and does not change.

Roof load limits (cab) vs canopy load ratings (not the same thing)

This trips up a lot of people. There are actually four different load ratings that matter when you put something on top of your vehicle:

  1. Vehicle cab roof rating (dynamic): This is how much weight the cab roof structure can handle while driving. For the Shark 6, aftermarket rack manufacturers rate their products at around 75 kg dynamic on the cab roof using the factory rails. That is low compared to some diesel utes with rain gutter or track mount systems.
  2. Vehicle cab roof rating (static): The weight the cab roof can handle when the vehicle is parked. The general industry rule of thumb is roughly three to four times the dynamic rating, so around 225 to 300 kg. This is what matters for a rooftop tent at camp.
  3. Canopy roof rating: This is separate from the vehicle roof. An aftermarket aluminium canopy might have its own roof rated at 100 to 250 kg dynamic and 300 to 500+ kg static. This rating depends on the canopy’s internal structure, materials and how it is mounted. It has nothing to do with the vehicle cab roof.
  4. Rack or platform rating: The roof rack or platform itself has a load rating. But the lowest number in the chain always wins. If your rack can hold 100 kg but the surface it is mounted to only allows 75 kg, then 75 kg is your limit.

The BYD Shark 6 roof load limits guide covers the four rating system, worked calculations and common mistakes in detail.

Common mistake: Assuming a 200 kg rated canopy roof means you can load 200 kg onto the canopy while driving. You also need to subtract the weight of the rack itself and any permanently mounted accessories (light bar, shovel holders, etc.) from that number. And all of it still counts toward your total payload.

Off road derating: Most manufacturers recommend reducing dynamic load ratings by approximately 30% or more on unsealed roads. So a 75 kg dynamic rating on bitumen might drop to around 50 kg on corrugated dirt. Always check your rack and canopy manufacturer’s specific guidance.

Towing + towball load interacts with your canopy build

The towing picture changed significantly when the Performance variant launched.

Premium: 2,500 kg braked, 750 kg unbraked, 250 kg max towball, 5,750 kg GCM. Performance: 3,500 kg braked, 750 kg unbraked, 350 kg max towball, 6,650 kg GCM.

Both variants share a 3,500 kg GVM. Here is the part that catches people out: towball download counts as payload. If you are towing a caravan with a 200 kg ball weight, that 200 kg comes straight off your available payload. With a standard 790 kg payload (Premium), a heavy canopy build, a driver and a passenger, you can hit the GVM wall well before you hit the towing limit.

On the Premium, the GCM of 5,750 kg means you cannot legally run both GVM (3,500 kg) and maximum towing (2,500 kg) at the same time (3,500 + 2,500 = 6,000 exceeds 5,750). The Performance’s 6,650 kg GCM provides significantly more headroom for combined vehicle and trailer weight.

The BYD Shark 6 towing capacity and setup guide covers the full towing interaction with payload, brake controllers, trailer wiring and towing mode behaviour. The BYD Shark 6 towing specs guide covers the variant by variant numbers.

Canopy vs hard lid vs roller shutter vs tonneau: what suits the Shark 6 best?

Choosing the right tub cover is the biggest single decision in your build. Each option has a genuine use case and each has trade offs. The BYD Shark 6 canopy vs hard lid vs roller shutter guide covers the full comparison in detail.

When a full canopy is the right answer

A canopy gives you the most enclosed volume, the best weather and dust sealing, the most mounting options for internal shelving and drawers and the strongest platform for roof mounted accessories. If you need any of the following, a canopy is the way to go:

  • Secure lockable storage for tools or touring gear
  • Dust sealed internal space for long dirt roads
  • Internal shelving, drawers or a fridge that stays mounted permanently
  • A solid base for a rooftop tent, heavy roof rack load or large awning
  • A sleeping platform inside the canopy (overlanding builds)

On the Shark 6 specifically, aluminium canopies make the most sense because they offer the best strength to weight ratio and weight is something you cannot waste on this vehicle. Current Shark 6 aluminium canopies range from approximately 52 kg (Alu Cab Explorer) to approximately 74 kg (Bush Company CapRax), while fibreglass options sit at 90 to 100 kg. The aluminium vs fibreglass canopy comparison for BYD Shark 6 covers the weight, strength and roof load differences in detail.

The aftermarket now includes aluminium canopies from Ironman 4×4 (Raid), Alu Cab (Explorer, Contour), Bush Company (CapRax Xpedition, Xtreme), MW Toolbox, Canetoad (TradeCap) and Savage Tech (Predator), plus fibreglass options from Caddy (Alpha GSX), Razorback and UniUte (Force Pro). Prices range from approximately $1,900 for entry level aluminium to approximately $6,650 for premium brands.

Downsides: A canopy adds height (affecting garage clearance and aerodynamics), adds significant weight to your payload budget and cannot be easily removed when you need full tub access for bulky loads.

When a hard lid is the smarter choice

A hard lid (sometimes called a load lid or flush lid) sits flat across the top of the tub, creating a weatherproof, lockable cover without the height or weight of a full canopy. Good aluminium hard lids for the Shark 6 weigh around 50 to 70 kg and premium models like the Utemaster Load Lid can carry up to 200 kg dynamic on their surface, which is enough for crossbars, a small cargo basket or even a rooftop tent at camp (check static ratings).

Choose a hard lid if you want security and weather protection without the canopy bulk, if you need to carry loads on top occasionally (crossbars, bikes, kayak), if you value a clean, low profile look or if you want the option to remove the lid for tip runs or furniture pickups.

Downsides: No internal shelving. Limited headroom means no fridge slide, no standing height access and no internal drawer systems taller than the tub depth (517 mm).

Roller shutter reality check (security vs access vs water and dust)

Roller shutters (also called roll top or retractable covers) look slick and provide decent security. Ironman offers manual (from approximately $2,549) and electric (from approximately $3,357) roller covers as official BYD accessories. HSP and other aftermarket brands offer Shark 6 shutters from approximately $1,200.

Choose a roller shutter if you want quick tub access without lifting a heavy lid, if security is important but you do not need full enclosure or if you want to pair the shutter with a tub rack above for carrying long items.

Downsides: Roller shutters have limited load ratings on the shutter surface itself (often 25 to 40 kg dynamic). They do not seal as well as a canopy for dust or heavy rain. You cannot mount a fridge slide or internal accessories. They can ice up or jam in very cold conditions. And they offer zero ventilation for a dog or airflow dependent gear.

Common mistake: Buying a roller shutter and then realising you cannot mount any meaningful load on top without also adding a separate tub rack, which then adds weight and cost. If you need roof carry capability, a hard lid or canopy often works out better value.

Soft tonneau (cheap, light, but not a touring solution)

A soft tonneau cover is the lightest and cheapest option. It keeps rain and casual eyes off your gear. That is about it. Starting from $300 to $650.

Comparison table

Feature Full canopy Hard lid Roller shutter Soft tonneau
Weight 52 to 100+ kg 50 to 70 kg 20 to 35 kg 5 to 10 kg
Security Excellent Good Good Poor
Dust sealing Excellent Good Fair Poor
Water sealing Excellent Very good Good Fair
Roof carry (dynamic) 100 to 250 kg (canopy rated) Up to 200 kg (lid rated) 25 to 40 kg None
Internal storage options Drawers, shelves, fridge Limited (tub depth only) None None
Best for Tradies, tourers, overlanders Weekenders, mixed use Quick access, clean look Budget, temporary
Price range (approx.) $1,900 to $6,650+ $1,600 to $3,900+ $1,200 to $3,357 $300 to $650

Canopy fitment on the Shark 6: mounting, sealing and the stuff that causes headaches later

Getting a canopy to sit properly on the Shark 6 is not a bolt and forget job. The mounting style, tub liner, sealing approach and sensor/camera integration all need to be right. The BYD Shark 6 clamp on vs bolt on canopy mounting guide covers the mounting method trade offs in detail.

Mounting styles (clamp on vs bolt on vs rail systems)

Clamp on: The canopy grips the tub lip using external clamps. No drilling into the tub. Easier to remove. Slightly less rigid than bolt on. This is the most common method for the Shark 6 because it preserves the tub structure and keeps things reversible.

Bolt on (through tub): Bolts pass through the tub lip or sides into the canopy base. Stronger and more secure. Better for heavy roof loads. But it requires drilling the tub, which can create rust points if not sealed properly and may affect vehicle warranty depending on your dealer’s stance.

Rail or channel systems: Some premium canopies use proprietary rail systems that sit on or clamp to the tub rails. These offer good rigidity without through drilling but tend to cost more.

What we recommend at Oz Canopies & 4×4: For most Shark 6 owners, clamp on mounting with a quality rubber seal strip gives you the best balance of strength, removability and peace of mind. If you are running a heavy touring build with a rooftop tent on the canopy, bolt on or a premium rail system is worth the extra investment for rigidity.

Tub liner, spray in liner and why it changes fitment

The Shark 6 comes with a factory spray in bedliner. This is actually a good thing for tub protection, but it adds a layer of material that canopy manufacturers need to account for. The spray in liner slightly reduces the internal tub dimensions, especially at the lip where the canopy sits. If you later add a drop in plastic tub liner on top of the spray in, the stacked thickness at the tub lip can interfere with canopy clamp fit and sealing compression.

Cab to canopy gap, dust ingress and pressure management

The gap between the back of the cab and the front of the canopy is the number one dust entry point on any ute. A flexible rubber dust seal strip bridging the cab to canopy gap is essential for any touring build. A positive pressure vent (a small vent that forces filtered air into the canopy, creating positive internal pressure) is the single most effective dustproofing measure for long dirt road trips.

The BYD Shark 6 dustproofing guide covers the full step by step sealing process including tailgate seals, cable grommets, positive pressure vents, light leak testing and real dirt road testing.

Rear vision, brake lights and sensors

The Shark 6 has a rear view camera, rear parking sensors and factory LED brake lights in the tailgate. When fitting a canopy, make sure the canopy rear window does not obstruct the reversing camera, get any canopy brake lights wired by a qualified auto electrician (the Shark 6 is a PHEV with integrated electronics and amateur wiring can cause CAN bus issues) and avoid canopy configurations that create reflections or glare in the rear camera view.

Power and electrics in a PHEV ute: clean, safe ways to run accessories

This is where the Shark 6 guide becomes genuinely different from anything written about a HiLux or Ranger diesel. The Shark 6 has a large lithium iron phosphate (LFP) battery and a built in vehicle to load (V2L) system that can change how you approach your entire electrical build.

V2L in the tub (how it changes your camping and work setup)

The current Shark 6 range confirms 230 V Type I cargo area V2L sockets across all pickup variants. The system draws from the 29.58 kWh LFP battery and can operate with the vehicle locked.

For tradies, this is a game changer. You can run or charge power tools on site straight from the ute’s battery. For tourers, it means you can plug in standard household appliances at camp. The BYD Shark 6 V2L power guide covers the full V2L system including discharge timers, SOC management, SAVE mode strategy and the 3 tier power framework.

But there are limits:

  • V2L drains the vehicle’s drive battery. If you drain it too far, you lose electric driving range.
  • The energy manager lets you set a minimum state of charge (SoC) between 25 to 70%, which helps prevent over discharge.
  • V2L runs at 230 V AC. If you need 12 V DC for accessories like LED strips, water pumps or compressor fridges, you will still need a 12 V system or an AC to DC converter.
  • The default V2L discharge duration is 5 hours. Adjust it through the infotainment settings.
  • The handbook says not to discharge below 15% battery capacity.

Common mistake: Planning an entire touring electrical system around V2L without a backup 12 V battery. V2L is brilliant for short trips, but for multi day remote touring where you want a fridge running 24/7 without worrying about drive battery depletion, a separate lithium battery with DC DC charging is still the more reliable approach.

12 V accessory limits and why people blow fuses

The Shark 6 has a standard 12 V accessory socket in the cabin rated at under 10 A and under 120 W, only available when the ignition is on. That is enough for a phone charger or a small tyre inflator. It is not enough for a fridge, LED lights, a water pump or any combination of 12 V accessories you would run in a canopy.

Best practice for 12 V accessories:

Install a fused distribution panel near the canopy for all your accessories. Use appropriately gauged wiring for each circuit. Run a dedicated feed from a secondary battery to the distribution panel. Fuse every circuit individually. The BYD Shark 6 canopy electrical wiring guide covers the full 12 V system design including DC DC chargers, fuse sizing, cable gauge and PHEV specific installation cautions.

Touring power layouts (3 tiers)

Tier 1: Simple (weekend trips, powered campsites)

  • V2L handles everything: fridge, lights, phone charging
  • Small 12 V fuse box for LED canopy lights and a water pump
  • No secondary battery
  • Cost: $0 to $500 for 12 V distribution and wiring

Tier 2: Serious (multi day trips, unpowered bush camps)

  • 100 Ah lithium battery (slimline, under a drawer or on the canopy floor)
  • DC DC charger to top up the lithium from the vehicle’s 12 V system while driving
  • Solar input (portable panel, 120 to 200 W) for extended stops
  • 12 V compressor fridge on a dedicated circuit
  • LED lighting and USB outlets off the lithium battery
  • V2L as a backup or for 230 V tools and appliances
  • Cost: $1,500 to $3,500 depending on battery brand and solar setup

Tier 3: Remote (week plus trips, no external power)

  • 200 Ah+ lithium battery bank
  • 1,000 to 2,000 W pure sine wave inverter for 230 V output independent of V2L
  • Fixed roof mounted solar panels (200 to 400 W) on the canopy roof
  • Battery monitor for real time state of charge tracking
  • Full 12 V distribution panel with individual circuit breakers
  • V2L used only for high draw 230 V tools or as a rapid battery charger
  • Cost: $4,000 to $8,000+

Where to mount batteries, chargers and compressors in a canopy build

Battery: Mount in a ventilated, water protected space. Under the drawer system is popular. Ensure the battery is restrained to meet load restraint requirements. The NTC Load Restraint Guide for Light Vehicles provides the baseline standard for securing cargo and equipment.

DC DC charger: Mount near the battery (ideally within about 1 metre) for best charging efficiency. Ensure adequate airflow.

Compressor: Mount in an accessible location with airflow for cooling. Not sealed in a cupboard.

Cable runs: Keep 12 V and 230 V wiring separated. Use conduit or loom protection. Secure all cables to prevent chafing.

Storage and organisation: tradie ready and touring ready layouts

Getting the internal layout right is the difference between a canopy that works for you every day and one that drives you mad. The Shark 6’s tub dimensions (1,520 x 1,500 x 517 mm) give you solid room to work with and the 1,224 mm floor width between the wheel arches is your primary constraint for drawer and shelf width.

The BYD Shark 6 fridge and drawer setup guide covers the 1,224 mm floor width constraint, fridge first design approach, slide types, structural mounting and NTC load restraint requirements in detail.

Tradie setup blueprint (secure + fast access)

A tradie build needs to be secure overnight, fast to access on site and organised enough that you are not digging through a pile of gear to find a specific fitting.

Key components: Drawer system (2 or 3 drawers) mounted across the full tub width behind the wheel arches with locking drawer slides rated for the weight you will carry. Shelving or racking above drawers with adjustable shelf heights so you can adapt as your tool inventory changes. Gullwing or flip up side windows for direct access to tools without walking to the tailgate every time. Tie down rails for securing loose items, tool rolls or bungee cords. A pipe and conduit carrier on the canopy roof if you carry lengths of pipe, conduit or timber.

Estimated weight:

Component Weight (kg)
Drawer system (2 drawers) 35 to 55
Shelving unit 15 to 30
Tools and consumables 60 to 120
Canopy 70 to 95
Total 180 to 300 kg

With a standard 790 kg payload (Premium) and a driver (90 kg), this leaves around 400 to 520 kg for passengers, additional materials and any towing load. Tight but manageable for daily use without a trailer.

Touring/camping blueprint (fridge, water, recovery, sleep system)

A touring build is about self sufficiency: keeping food cold, carrying water, recovering yourself if you get stuck and sleeping comfortably.

Key components: Fridge slide mounted on the left or right side of the canopy floor, usually above a low profile drawer. A 40 to 60 L compressor fridge on a heavy duty slide lets you access the fridge from the canopy side window or tailgate. A drawer system (1 or 2 drawers) for cooking gear, cutlery, dry food and recovery equipment. Water storage of 2 x 20 L jerry cans secured in the canopy or a compact under tray tank (20 to 40 L) with gravity fed or 12 V pump distribution. Recovery gear including snatch strap, rated shackles, recovery boards and a basic tool kit stored on canopy wall mounts or in a dedicated recovery bag. An awning mounted to the canopy side rail (2.0 to 2.5 m is the sweet spot). An optional rooftop tent on the canopy roof (adds 40 to 70 kg including the tent and mounting rack) or an internal sleeping platform if the canopy is tall enough.

Estimated weight:

Component Weight (kg)
Canopy 75 to 95
Fridge slide + 50 L fridge 35 to 45
Drawer system (1 drawer) 20 to 35
100 Ah lithium battery + DC DC 15 to 20
Water (40 L) 40
Awning 18 to 25
Recovery gear 15 to 20
Cooking and camp gear 15 to 25
Total 233 to 305 kg

Add a rooftop tent (50 to 65 kg) and you are at 283 to 370 kg before passengers and fuel. On the Premium, that is legal but leaves limited room for towing. On the Performance, the 725 kg payload is tighter still. This is exactly the scenario where the Ironman GVM upgrade earns its money.

Mixed use blueprint (daily work + weekend trips)

The trick with a mixed use build is modularity. You want things you can add, remove or rearrange without tools or frustration.

  • Modular drawer system: Choose drawers that can be unbolted or slid out when you need the full tub floor.
  • Removable fridge slide: Quick release mounting so the fridge comes out for work days and goes back in for weekends.
  • Hard lid instead of canopy: Lets you carry tall items during the week and still have a secure, weatherproof tub.
  • Quick release crossbar system: Bars go on for weekend trips (bikes, kayak, cargo) and come off for low clearance parking.

Roof racks, platforms, awnings, rooftop tents: doing it without wrecking your weight budget

Roof mounted gear is where Shark 6 builds go off the rails (sometimes literally). The BYD Shark 6 roof racks and platforms guide covers the full rack landscape including Rhino Rack, Yakima, HSP, cab vs canopy vs tub rack options and three packaged builds.

Cab mount vs canopy mount vs tub rack

Cab mount (factory roof rails): The Shark 6 has factory raised roof rails on the cab. These accept crossbars and platforms from Rhino Rack (Sportz RX, Vortex RX, Pioneer 6) and Yakima (JetStream, LockNLoad). Dynamic load around 75 kg including the rack itself. Fine for bikes, boards and light cargo. Not enough for most rooftop tents while driving.

Canopy mount: If you have fitted an aluminium canopy, the canopy roof has its own independent load rating. Current Shark 6 aluminium canopies offer 100 to 250 kg dynamic depending on the brand. This opens up heavier loads including rooftop tents, platforms and awnings. The canopy distributes the load to the tub lip, not the cab roof.

Tub rack (standalone): A standalone tub rack mounts to the tub sides or tub rails independently of any canopy. The HSP Load Rack JNR is rated at 150 kg dynamic and 300 kg static. Works with or without a canopy and is popular for rooftop tent mounts on the Shark 6.

Factor Cab roof Canopy roof Tub rack
Dynamic load (typical) ~75 kg 100 to 250 kg 100 to 200 kg
Static load (typical) ~225 to 300 kg 300 to 500+ kg 300+ kg
RTT suitability Limited Good (if rated) Excellent
Tub access Full Limited by canopy Limited by rack
Cost range $400 to $2,000 $200 to $800 (on top of canopy cost) $800 to $2,500

Rooftop tent reality check

A typical rooftop tent (folded, with mounting hardware) weighs 50 to 70 kg. Add a platform or rack system at 15 to 25 kg and you are at 65 to 95 kg. That means many rooftop tents exceed the cab roof dynamic limit. Mount the rooftop tent on the canopy roof or a tub rack, where dynamic ratings of 150 to 250 kg are common. The BYD Shark 6 rooftop tent guide covers the weight calculations, tent options and mounting choices in detail.

Common mistake: Buying a rooftop tent and mounting it on the cab roof without checking whether the total weight (tent + rack + any accessories on the same rack) exceeds 75 kg dynamic. This is one of the most common overloading scenarios on the Shark 6.

Awnings, batwings and side loads

Awnings and batwings mount to the side of a canopy or to a roof rack. When deployed, they create significant side leverage on whatever they are mounted to. When packed (closed), the weight hangs off one side. Check the canopy manufacturer’s side load rating. Use purpose built awning brackets rated for the load. Always use guy ropes and pegs when deployed. A heavy batwing awning (15 to 25 kg) mounted at the roofline creates leverage that can stress the canopy to tub mounting over time, especially on corrugated roads.

Towing with a canopy build: what changes and how to stay legal and safe

Towing is a big deal for Australian ute owners and the Shark 6 range now spans two different towing classes.

The Shark 6 towing limits in plain English

Premium: 2,500 kg braked. Covers most single axle caravans, box trailers with equipment, boat trailers and many tandem axle trailers under about 2,200 kg loaded.

Performance: 3,500 kg braked. Matches the diesel ute benchmark. Covers almost all single and tandem axle caravans, larger boat trailers and heavier plant trailers.

Both: 750 kg unbraked and 3,500 kg GVM.

Why towball mass is the silent payload killer

Every kilogram of towball download is a kilogram less payload for passengers, canopy, tools and gear. With 250 kg on the ball (Premium max) or 350 kg (Performance max), a significant portion of your payload is consumed before you put anything in the tub.

Quick example (Premium):

Item Weight (kg)
Driver + passenger 180
Canopy + fitout 170
Towball download 200
Spare gear in tub 30
Total 580 kg used, 210 kg remaining

That 210 kg remaining is your buffer. It is legal, but it is tight. Now imagine you also strapped a 50 kg rooftop tent to the canopy roof and mounted a 25 kg awning. You are at 655 kg used, with 135 kg left and one extra passenger puts you over.

On the Performance with 725 kg payload, the same 580 kg used leaves only 145 kg remaining. The higher towball allowance (350 kg) actually makes GVM compliance harder because it enables heavier trailers that transfer more weight onto the vehicle.

This is why payload, towing and canopy builds all need to be planned together, not separately.

Brake controllers, trailer wiring and practical setup tips

The Shark 6 does not have a factory fitted brake controller. Electric brake controllers from Redarc (Tow Pro Elite, Liberty), Hayman Reese (Guardian IQ) and Elecbrakes (wireless) are compatible. Have it wired by a qualified auto electrician who understands the Shark 6’s electrical architecture.

When the Shark 6’s 7 pin trailer plug is connected, towing mode activates automatically. This disables adaptive cruise control, AEB, lane keep assist, blind spot detection and several other driver assistance features. Speed is limited to 110 km/h. The vehicle defaults to NORMAL drive mode only.

Off road, water crossings, dust and long term durability

The Shark 6 has respectable off road specs: 230 mm ground clearance, 700 mm wading depth, a 31 degree approach angle and terrain modes for mud, sand and snow.

Crawl Mode (new for 2026)

The Performance introduces Crawl Mode, which limits speed to approximately 20 km/h and continuously adjusts torque to minimise wheel spin on steep, slippery or rocky terrain. BYD says it works best around 12 km/h. Crawl Mode will be rolled out to Premium and Dynamic variants via an over the air update later in 2026.

The Shark 6 still lacks low range gearing and locking differentials (these are reserved for the related Denza models). For fire trails, beach driving and moderate bush tracks, it is capable. For serious rock crawling and deep rut work, it has its limits.

Water sealing basics (what “water resistant” actually means)

When canopy manufacturers say “water resistant,” they mean the canopy will keep out rain and road spray under normal driving conditions. They do not mean you can submerge it in a river crossing and expect a dry interior.

For water crossings, ensure all canopy seals (tailgate, side doors, windows, cab to canopy gap) are properly compressed and in good condition. Seal any drill holes or cable entry points with marine grade sealant. Check the canopy floor for drainage because water that enters needs a way out.

Dustproofing basics (pressure vents and sealing points)

The full dustproofing checklist includes a cab to canopy seal strip (closed cell rubber, proper compression), tailgate seal (replace or upgrade if factory seal is inadequate), window and door seals (check for gaps when closed), a positive pressure vent (filtered air ram, mounted at the front of the canopy), sealed cable and wiring entry points (silicon or grommet) and a light leak test after fitting (any light leaking in is a dust path).

The canopy maintenance and waterproofing guide covers seasonal inspection, seal replacement, drainage and the diagnostic process for finding water leaks.

Wading depth and what to protect

The Shark 6 has a listed wading depth of 700 mm. That is measured to the bottom of the tub floor. If you are crossing water deeper than about 300 mm, consider where your canopy floor electronics are mounted (battery, DC DC charger, fuse box). Mount electronics above the tub rail height where possible. Seal important documents and electronics in dry bags. Make sure the V2L outlet flap is closed before any water crossing.

Legal and compliance basics in Australia (canopy installs, loads, mods)

The canopy and accessory modifications legal requirements guide covers the full compliance framework including VSB 14, ADRs, state certification pathways and PHEV specific installation cautions.

Load restraint: your responsibilities (quick summary)

Under Australian law, the driver is responsible for ensuring all cargo is properly restrained. The National Transport Commission’s Load Restraint Guide for Light Vehicles is the baseline reference. Loads must be restrained to prevent movement in all directions: forward (80%), rearward (50%), sideways (50%) and upward (20%). A canopy is a form of containment, but heavy items inside still need to be individually secured or blocked.

Vehicle modification frameworks (when you should ask an engineer)

The national baseline for vehicle modifications is VSB 14. For canopy builds, clamp on installation typically does not require engineering certification. GVM upgrades require a certified engineer and compliance plate change. Bull bars must comply with applicable ADRs. Suspension modifications beyond permitted limits may require sign off. Electrical modifications must comply with relevant ADRs for lighting. Transport for NSW handles the administrative side in NSW, with VASS (Vehicle Assessment Signatory Scheme) in Victoria and equivalent frameworks in other states.

Buying guide: how to choose the right canopy without regret

The Shark 6 canopy market has matured rapidly since the vehicle’s late 2024 launch.

Current Shark 6 canopy market (August 2026)

Aluminium (from approximately $1,900 to $6,650): Ironman 4×4 Raid (65 kg, 180 kg dynamic), Alu Cab Explorer (52 kg, 200 kg dynamic), Alu Cab Contour (67 to 74 kg, 200 kg dynamic), Bush Company CapRax Xpedition (74 kg, 250 kg dynamic, from $5,950), Bush Company CapRax Xtreme (74 kg, 250 kg dynamic, from $6,650), MW Toolbox (65 kg, 150 kg dynamic), Canetoad TradeCap (65 to 70 kg, 180 kg dynamic) and Savage Tech Predator (150 kg dynamic).

Fibreglass (from approximately $3,500 to $4,400): Caddy Alpha GSX (95 to 100 kg, central locking), Razorback (90 to 100 kg, 100 kg dynamic on road) and UniUte Force Pro (90 kg).

Bull bars: Ironman Deluxe (steel hooped, winch ready), Ironman Raid (aluminium, hoopless), Ironman Nudge Bar, ARB Zenith Bar (hoopless, dual 8T recovery points), Offroad Animal Toro and Predator, Hamer King Series.

Roller shutters: Ironman manual (from approximately $2,549), Ironman electric (from approximately $3,357), HSP (from approximately $1,200).

Hard lids: Budget tri fold (from approximately $1,600), premium load rated (from approximately $2,500 to $3,900).

Suspension and GVM: Ironman GVM upgrade kits (Medium $3,490, Heavy $3,590, Extra Heavy $3,690).

The questions to ask before you pay a deposit

  1. Is this canopy specifically designed for the BYD Shark 6?
  2. What is the exact canopy weight?
  3. What is the roof load rating (dynamic and static)?
  4. How is it mounted (clamp on, bolt on or rail)?
  5. What is the lead time?
  6. What is the warranty?
  7. Can the canopy accept roof racks, awnings or a rooftop tent?
  8. What about colour match?
  9. Does it come with internal lighting, wiring provisions or a locking mechanism?
  10. Can I see one fitted to a Shark 6 before I buy?

Spec checklist (copy and paste this)

Use this when comparing canopy quotes:

  • Canopy material (aluminium / fibreglass / steel / ABS)
  • Total weight (kg)
  • Roof load rating: dynamic (kg) / static (kg)
  • Mounting type (clamp / bolt / rail)
  • Window type (sliding / lift up / fixed / solid panel)
  • Ventilation (positive pressure vent compatible / built in vents)
  • Internal lighting (LED strips / dome light / none)
  • Internal roof tracks or channels
  • Tie down rails or anchor points
  • Integrated brake light (wired / not wired)
  • Locking system (key / central lock compatible / padlock)
  • Colour match (factory colour code / custom / standard black or white)
  • Seal type (rubber / foam / compression strip)
  • Warranty (structural / paint / seals / duration)
  • Lead time (in stock / made to order / weeks)
  • Price (supply only / supply and fit)

Warranty and insurance notes

A clamp on canopy installation should not void your BYD vehicle warranty. Bolt on installations that require drilling the tub could be questioned on tub related claims. Keep all fitting documentation and receipts. Notify your insurer when you add a canopy and accessories. Undisclosed modifications can result in a rejected claim.

Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney to compare canopy options for your Shark 6 build.

Recommended Shark 6 canopy setups (3 complete packages)

These are complete build frameworks with component categories, weights and power approaches that you can hand to any good fitter and say “build this.”

1. Shark 6 Tradie Security Package

What you are solving: Secure tool storage, organised access on site, basic lighting and the ability to run power tools off the ute.

Component Category Est. weight (kg)
Aluminium canopy (solid side panels, rear barn doors) Canopy 80
Central locking (keyed alike or remote) Security 2
LED interior strip lighting (2 strips) Lighting 1
2 drawer system (full width, locking slides) Storage 45
Adjustable shelf unit above drawers Storage 20
Crossbar set on canopy roof (pair) Roof carry 8
Rubber cab to canopy dust seal Sealing 1
Total (canopy + fitout) ~157 kg

Power approach: V2L handles all power tool charging and on site use. A small 12 V fuse box powers the LED lighting off the vehicle’s 12 V system.

Payload note (Premium): With the driver (90 kg) and fitout (157 kg), you have used 247 kg. That leaves approximately 543 kg for tools, materials, a passenger and any towing load.

2. Shark 6 Touring Weekender Package

What you are solving: Comfortable self sufficient camping for 2 to 5 day trips.

Component Category Est. weight (kg)
Aluminium canopy (sliding windows, rear lift up window) Canopy 85
Fridge slide (heavy duty, 900 mm) Storage 15
50 L compressor fridge Cooling 22
Single drawer unit under fridge slide Storage 25
100 Ah slimline lithium battery Power 12
DC DC charger (25 A) Power 2
12 V fuse box (6 way) + wiring Power 3
2 x 20 L water jerry cans Water 40 (full)
2.0 m awning (canopy side mount) Shade 18
Positive pressure dust vent Sealing 1
Recovery kit (snatch strap, shackles, MaxTrax) Recovery 15
Cab to canopy dust seal Sealing 1
Total (canopy + fitout, water full) ~239 kg

Payload note (Premium): Driver (90 kg) + fitout (239 kg) = 329 kg used, leaving approximately 461 kg. Add a passenger and you are at roughly 371 kg remaining. Legal and comfortable on standard GVM for a couple doing a long weekend.

3. Shark 6 Long Trip Remote Package

What you are solving: Extended remote touring (1 to 3 weeks). Full self sufficiency. This build assumes a GVM upgrade.

Component Category Est. weight (kg)
Aluminium canopy (gullwing sides, rear lift up, internal tracks) Canopy 90
Rooftop tent (canopy mounted, compact 2 person) Sleep 55
Roof platform on canopy (for tent + solar) Roof carry 20
200 W fixed solar panel Power 12
200 Ah lithium battery Power 22
DC DC charger (40 A) + battery monitor Power 4
2,000 W pure sine inverter Power 8
12 V distribution panel (8 way) + wiring Power 4
Fridge slide + 60 L fridge Cooling 28
2 drawer system Storage 40
80 L water tank + 12 V pump Water 85 (full)
2.5 m awning (canopy side mount) Shade 22
Positive pressure dust vent Sealing 1
Full recovery kit Recovery 18
Tyre inflation compressor Tools 5
Cab to canopy dust seal Sealing 1
Total (canopy + fitout, water full) ~415 kg

Payload note: On the Premium with a GVM upgrade (1,140 kg payload), driver (90 kg) + passenger (80 kg) + fitout (415 kg) = 585 kg used, leaving approximately 555 kg. Enough for towing a small trailer and carrying additional gear.

What we recommend at Oz Canopies & 4×4: If you are planning a remote touring build on the Shark 6, get the GVM upgrade sorted before you commit to the build. It changes the entire equation.

FAQs

What are the BYD Shark 6 tub dimensions?

The tub measures 1,520 mm long, 1,500 mm wide at the top and 517 mm deep. The width between the wheel arches at floor level is approximately 1,224 mm. Total tub volume is 1,200 litres. Both Premium and Performance pickups share the same tub.

What is the real payload once you add a canopy?

On the Premium with approximately 790 kg payload, a typical aluminium canopy (52 to 95 kg) leaves you with roughly 695 to 738 kg before adding anything else. Once you add a driver (90 kg), the remaining budget for passengers, gear, drawers and towing drops to 605 to 648 kg. On the Performance with approximately 725 kg payload, every figure is 65 kg tighter.

What are the Shark 6 roof load limits?

The cab roof supports approximately 75 kg dynamic (while driving) and around 225 to 300 kg static (while parked). Aftermarket canopy roofs have their own separate ratings, often 100 to 250 kg dynamic and 300 to 500+ kg static, depending on the brand and construction.

Can I run a fridge off the tub power outlets?

Yes, but with caveats. The V2L outlets provide 230 V AC. This drains the vehicle’s drive battery, so it is best suited for short trips or situations where you can set a minimum state of charge. For multi day trips, a separate 12 V system with a compressor fridge is more reliable.

What is the max towball load?

250 kg on the Premium, 350 kg on the Performance. This is the maximum downward force the loaded trailer can exert on the towball. Every kilogram of towball download counts against your payload.

Can I fit a rooftop tent safely on the cab roof vs on the canopy?

On the cab roof: only if the tent, rack and mounting hardware weigh under 75 kg combined (dynamic). Many rooftop tents exceed this once the rack is added. On a properly rated canopy roof or tub rack: yes, with dynamic ratings of 150 to 250 kg being common. Canopy mount or tub rack mount is the safer and more practical option for most setups.

Can the Performance tow 3,500 kg?

Yes. The 2026 Shark 6 Performance has 3,500 kg braked towing capacity, 350 kg towball load and a 6,650 kg GCM. This matches the diesel ute benchmark set by HiLux and Ranger.

Does the Performance use the same canopy as the Premium?

Yes. Both pickups share identical tub dimensions (1,520 x 1,500 x 517 mm). Any canopy designed for the Shark 6 pickup fits both variants.

What is Crawl Mode?

Crawl Mode is a new feature that debuted on the Performance variant. It limits speed to approximately 20 km/h and continuously adjusts torque for improved off road traction. BYD will roll it out to Premium and Dynamic variants via OTA update later in 2026.

Is 2,500 kg towing enough?

For most single axle caravans, camper trailers, boat trailers and work trailers under about 2,200 kg loaded, yes. If you need more, the Performance variant tows 3,500 kg.

How do I stop dust getting into a Shark 6 canopy?

Four things: a cab to canopy rubber dust seal, a positive pressure filtered vent, sealed cable entry points and proper tailgate and window seals. Check for light leaks with a torch in daylight after your first dirt road trip.

Clamp on vs bolt on: which is better for the Shark 6?

Clamp on is better for most owners. It is non destructive, easier to remove and carries less warranty risk. Bolt on is stronger and better sealed, making it the right choice for heavy touring builds with roof mounted loads. Choose based on your build weight and whether you plan to remove the canopy regularly.

Does a tub liner affect canopy sealing?

Yes. The factory spray in liner adds material at the tub lip, which affects how canopy clamps and seals compress. Adding a drop in liner on top of the spray in can cause issues. Measure and test fit before committing.

Do I need a GVM upgrade for a heavy touring build?

Almost certainly yes if your canopy fitout, passengers and gear approach 500+ kg. The Ironman GVM upgrade lifts payload to approximately 1,140 kg on the listed Premium configuration. Kits start from $3,490.

What canopy material is best for the Shark 6?

Aluminium. It offers the best strength to weight ratio and weight savings matter more on the Shark 6 than almost any other ute due to the tighter payload.

Can I still use the V2L outlets with a canopy fitted?

Yes. The V2L outlets sit under a flap on the driver side of the tub. Make sure your canopy design does not obstruct access to this flap.

Does the Shark 6 have cruise control while towing?

Not currently. Adaptive and intelligent cruise control are disabled in towing mode. BYD has acknowledged this and indicated potential OTA updates may address it.

Does the Shark 6 have a GCM rating?

Yes. The GCM is 5,750 kg on the Premium and 6,650 kg on the Performance. This is the maximum total weight of the loaded vehicle plus the loaded trailer combined.

What is the Shark 6 wading depth?

700 mm. If you have electronics or batteries mounted on the canopy floor, consider raising them above the tub rail to protect against water entry during crossings.

Will fitting a canopy void my BYD warranty?

A clamp on canopy installation should not void your warranty, as it does not modify the vehicle structure. Bolt on installations that drill the tub could potentially be challenged on tub related claims. Keep all fitting documentation and receipts.

How heavy is a typical aluminium canopy for the Shark 6?

Current Shark 6 aluminium canopies range from approximately 52 kg (Alu Cab Explorer) to approximately 74 kg (Bush Company CapRax). Premium canopies with integrated gullwing doors and internal tracks tend to be at the heavier end. Fibreglass options sit at 90 to 100 kg.

Can I fit an electric brake controller in the Shark 6?

Yes. Aftermarket brake controllers from Redarc, Hayman Reese and others are compatible. Have it installed by a qualified auto electrician who understands the Shark 6’s PHEV electrical system.

What locks are most secure for a Shark 6 canopy?

Central locking systems (keyed alike or tied to the vehicle’s remote) are the most convenient. For maximum security, look for canopies with multi point locking (top and bottom latches on each door) and tamper resistant hardware.

Is there a canopy specifically designed for the Shark 6?

Yes. Multiple aftermarket manufacturers now produce Shark 6 specific canopies in both aluminium (Ironman, Alu Cab, Bush Company CapRax, MW Toolbox, Canetoad, Savage Tech) and fibreglass (Caddy, Razorback, UniUte). The market has grown significantly since the vehicle’s late 2024 launch.

Can I fit a canopy and still tow?

Absolutely. Just ensure your total loaded weight (vehicle + canopy + fitout + passengers + towball download) stays within GVM. Use the payload section in this guide to check your numbers before you commit.

What is the Dynamic Cab Chassis?

The Dynamic is a cab chassis variant ($55,900) with no factory tub. It requires a separately fitted tray or service body. An optional Ironman alloy tray is available. It uses the Premium’s powertrain and tows 2,500 kg.

Glossary

GVM (Gross Vehicle Mass): The maximum legal total weight of the vehicle including everything on it. The Shark 6 standard GVM is 3,500 kg across all variants.

Kerb weight: The weight of the vehicle as manufactured, with all fluids and a full tank of fuel, but no cargo, passengers or aftermarket accessories. Premium: 2,710 kg. Performance: 2,775 kg.

Payload: The difference between GVM and kerb weight. Premium: approximately 790 kg. Performance: approximately 725 kg.

GCM (Gross Combination Mass): The maximum total weight of the loaded vehicle plus the loaded trailer. Premium: 5,750 kg. Performance: 6,650 kg.

Towball download (vertical load): The downward force the loaded trailer exerts on the towball. Premium maximum: 250 kg. Performance maximum: 350 kg. This counts toward your payload.

Dynamic roof load: The weight a roof, rack or canopy can carry while the vehicle is moving. Lower than static because of vibration, acceleration and cornering forces.

Static roof load: The weight a roof, rack or canopy can handle when the vehicle is parked. Typically 3 to 4 times the dynamic rating.

V2L (Vehicle to Load): A system that allows the vehicle’s drive battery to supply AC power (230 V in Australia) through outlets in the tub or cabin.

VSB 14: Vehicle Standards Bulletin 14, the national code of practice for light vehicle construction and modification in Australia. Published by the Department of Infrastructure, Transport, Regional Development, Communications and the Arts.

ADR (Australian Design Rules): The national standards for vehicle safety, emissions and anti theft. Aftermarket accessories must comply with relevant ADRs where applicable.

NTC Load Restraint Guide: The National Transport Commission’s guide covering how loads must be restrained in and on vehicles.

DC DC charger: A device that charges a secondary (auxiliary) battery from the vehicle’s main electrical system while driving.

PHEV (Plug in Hybrid Electric Vehicle): A vehicle with both an internal combustion engine and an electric motor/battery, where the battery can be charged from an external power source.

Crawl Mode: A low speed off road mode that limits speed to approximately 20 km/h and adjusts torque to minimise wheel spin. Available on the Performance variant, coming to other variants via OTA update.

Want us to sanity check your build list?

Planning a canopy for BYD Shark 6 and want to make sure the numbers add up? Drop into the Oz Canopies & 4×4 showroom in South Windsor or give us a call. We will run through your payload maths, check fitment compatibility and help you put together a setup that works for how you actually use your ute, whether that is a worksite every day, a touring rig every other weekend or something in between.

Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney.

Browse our full range of BYD Shark 6 accessories to see what is available and ready to fit right now.