Collection: Ford Ranger Towbars and Towing

Towbars and Plug N Play looms for the PX, PX2, PX3 and RA Next Gen Ranger, with separate bars for tub utes with the step, tray backs and extended trays. Plan the bar, wiring and hitch against your Ranger's real towing numbers.

Showing products for your

Showing 9 of 9 results

Gear up for adventure
Gear up for adventure
Limited time sale

Gear up for adventure

Save big on canopies, racks, drawers & morethis season

Rated to Tow, Limited by Weight

The Ranger is the ute we most often see hitched to a caravan, and most are rated at 3,500 kg braked. The exceptions matter. The Raptor is rated at 2,500 kg in both generations, and early PX 4x4s were rated at 3,350 kg before Ford lifted the figure. Check which of those you own before spending on a bar.

The braked rating is only the trailer limit. The Next Gen also has a gross combined mass of 6,350 kg on 2.0 litre bi turbo 4x4s, 6,400 kg on the V6 and 5,370 kg on the Raptor. Published comparisons show an XLT bi turbo keeping about 635 kg of payload with a 3,500 kg trailer, and a Wildtrak bi turbo about 586 kg. That margin has to cover people, a canopy, a fridge and anything else bolted on.

PX Bars for Every Body

PX, PX2 and PX3 Rangers built from 2011 to 07/2022 have three bodies to match: a tub with the factory step, a standard tray back, and a tray back with an extended tray, which takes its own bar. Tray back owners who head off road can choose TAG's Extreme Recovery bar, listed for PX Rangers and the 2011 to 2020 BT-50, which gives rated recovery points at the back. Recovery straps belong on those points and never on a tow ball.

Next Gen Bars From 08/2022

The RA Next Gen has a bar for the tub with step and another for tray back cab chassis utes. Our own Oz Canopies & 4x4 Next Gen towbar suits either body, which helps owners who may swap from tub to tray later. Nothing from the PX bolts to the Next Gen chassis, so upgrading your Ranger means a new bar. Compare the lot in Ranger towbars, or see the full towbar collection.

Cab Chassis Rangers on Work Duty

Tradies who tow every day often choose a cab chassis for good reason. Ford's figures for a Next Gen XLT double cab chassis with the V6 show 1,151 kg of payload, against roughly 1,000 kg for most double cab pickups, so there is more room for a tray, toolboxes and a ball load before the ute runs out of margin. A tray does weigh something, so subtract it. Pair a cab chassis Ranger with the tray back bar for its generation, or our Oz Canopies & 4x4 Next Gen bar, and keep the heaviest tools ahead of the rear axle.

Raptor Owners Need a Different Plan

At 2,500 kg braked, the Raptor suits a camper trailer, a jet ski or a light off road van far better than a big tourer. On the Next Gen Raptor, a gross combined mass of 5,370 kg and payload of around 700 kg leave little slack. If you want the Raptor's ride and a heavy van as well, talk to us before buying either.

Ranger Looms by Build Date

Ranger looms follow the build plate. A Plug N Play loom with an ECU module suits PX Rangers from 2011 to 07/2022, along with the BT-50 of 2011 to 08/2020. Another Plug N Play loom is listed for Rangers built 06/2015 to 12/2024, taking in PX2, PX3 and early Next Gen utes. Neither names a Ranger built in 2025 or later, so check with us before ordering for a late ute. Browse trailer looms to compare them.

A caravan big enough to need the full rating will run electric brakes, so plan a brake controller in the cab along with the loom.

Hitching a Heavy Van

Most Rangers towing near the limit are pulling a caravan, and a few setup choices help. Set the ball height with the ute packed for the trip, because 350 kg of download pulls the rear down noticeably. An adjustable mount lets you fine tune the van's attitude, and a weight distribution hitch can return some load to the front axle where Ford's guidance for your model allows it. Shanks, mounts, extenders and covers are in hitch accessories.

Plan Payload Before Buying the Van

A Ranger towing a 3,000 kg van usually carries a canopy, drawers, water and recovery gear as well. Add those up before you buy the van, not after. An aluminium canopy saves weight over steel, a lighter front bar helps too, and keeping water in the van's tanks rather than the tub moves weight off the ute. A weighbridge ticket for the loaded combination is the only number that counts.

Fitting Ranger Towing Gear

NSW customers can have Ranger bars and looms fitted together at our South Windsor workshop, with every trailer function tested before the ute leaves. We have been fitting out utes there since 1998, and parts also ship to Ranger owners across NSW and the rest of Australia. Explore every towing category for the rest.

Call us on 02 9627 8666, text 0440 130 098, or visit our showroom at 20 Walker Street, South Windsor NSW 2756.

Have questions?

My PX has an extended alloy tray. Will the standard tray back bar fit?

Choose the bar listed for a tray back with an extended tray. The standard tray back bar is for a regular length deck.

Can my Raptor tow a 3,000 kg van?

No. Both PX and Next Gen Raptors are rated at 2,500 kg braked, and the Next Gen Raptor's GCM is 5,370 kg.

Will my PX towbar fit my new Next Gen?

No. The chassis changed, so PX bars stay with the PX. Our Oz Canopies & 4x4 Next Gen bar suits a tub or a tray back.

How much payload is left when my Wildtrak tows 3,500 kg?

Published figures for the 2.0 litre bi turbo put the Wildtrak at about 586 kg with a 3,500 kg trailer, and the XLT at about 635 kg. Everything in the cab and tub must fit inside that.

Is a recovery towbar worth it on a PX tray back?

If you drive sand or mud often, yes. It gives rated points at the rear so straps never go on the ball. It is listed for PX tray backs and the BT-50 tray backs of the same era.

Should I use a weight distribution hitch with my Ranger?

It can level a heavy van, but check Ford's guidance for your model first and set it up with the van loaded. The shanks are in our hitch accessories.

Need help choosing?

Call us on 02 9627 8666 or chat with our team.