-
Generally in stock

Fits your
Fits selected models
Check fitment for your vehicle
Doesn’t fit your
RCS Retractable Canopy to Suit Dual Cab Australian Utes
Regular price $5,890Sale price $5,890 Regular price -
Fits your
Fits selected models
Check fitment for your vehicle
Doesn’t fit your
BYD Shark 6 2024 to Current Heavy Duty Aluminium Black Canopy
Regular price $2,499Sale price $2,499 Regular price$2,999-17% -
Fits your
Fits selected models
Check fitment for your vehicle
Doesn’t fit your
BYD Shark 6 2024 to Current Heavy Duty Steel Black Canopy
Regular price $1,999Sale price $1,999 Regular price$2,499-20%
BYD Shark 6 Canopy Range
The BYD Shark 6 is Australia's first plug in hybrid dual cab ute and it changes the canopy conversation. With a kerb weight north of 2,700 kg, tighter payload margins than most diesel utes, built in 230 V power outlets in the tub and independent rear suspension, the Shark 6 demands a different approach to canopy selection and build planning than a traditional ute.
At Oz Canopies & 4x4, we carry canopies specifically designed for the Shark 6's tub dimensions and unique characteristics. Whether you are building a touring setup, a work vehicle or adding secure everyday storage, every component choice needs to factor in the Shark 6's payload constraints.
Shark 6 Tub Dimensions and Fitment
The factory BYD Shark 6 pickup tub measures approximately 1,520 mm long, 1,500 mm wide and 517 mm deep, with approximately 1,224 mm between the wheel arches at floor level. The tub comes with a factory spray in bedliner which slightly reduces the usable internal dimensions.
These measurements are your starting point for canopy, drawer and storage fitment. Always measure your actual lined tub before ordering anything built to close tolerances, as the factory liner thickness and wheel arch contours can affect available space.
The 1,224 mm width between the arches is wide enough for a standard Australian pallet (1,165 x 1,165 mm), which is a genuine advantage for tradespeople.
Payload: The Shark 6's Critical Constraint
Payload is the single most important consideration for any Shark 6 canopy build. The Shark 6's large battery pack makes it significantly heavier than diesel utes of similar size, which means your available payload for canopy, accessories, passengers and cargo is tighter.
Before you order anything, calculate your actual remaining payload after passengers, the canopy itself and any towball load. If you are under 200 kg of headroom after adding a canopy, reconsider your build list or investigate a GVM upgrade. Aluminium canopies are strongly recommended over steel for the Shark 6 to preserve maximum payload for actual cargo.
V2L Power and Canopy Electrical Planning
The Shark 6 has three 230 V Vehicle to Load (V2L) power outlets in the tub. This built in power source can simplify your camping and worksite electrical setup by reducing or eliminating the need for a secondary battery system for some applications.
However, V2L runs from the main drive battery, which means using it for extended periods depletes your driving range. Decide early whether you plan to run accessories off V2L, off a separate 12 V system or both. This decision shapes your entire canopy electrical layout.
Canopy Materials for BYD Shark 6
Aluminium (Recommended)
Aluminium is the strongly recommended canopy material for the Shark 6. At 60 kg to 80 kg, an aluminium canopy minimises the impact on the vehicle's tight payload. It provides excellent corrosion resistance, supports roof loads for tents and platforms and is easy to modify for accessories.
Steel
Steel canopies are available for the Shark 6 but the additional weight (100 kg to 180 kg) makes a significant dent in your already limited payload. Only consider steel if your use case demands maximum structural strength and you have confirmed sufficient payload headroom.
Fitment and Delivery Information
Vehicle Compatibility
The Shark 6 is a single generation vehicle (2025+) available only as a dual cab. Canopies must be specifically designed for the Shark 6 tub, which has different dimensions from other dual cab utes. Do not attempt to fit a canopy designed for another vehicle.
Mounting Considerations
The Shark 6 uses clamp on mounting as the standard canopy installation method. Before drilling any holes for bolt on mounting, confirm what lies beneath the tub surface, as the high voltage battery and associated wiring run through the chassis. Incorrect drilling can be dangerous and void your warranty.
Professional Fitment Available
We offer BYD Shark 6 canopy installation at our Sydney showroom. Given the vehicle's unique hybrid system and payload constraints, professional fitment is particularly important for the Shark 6. Call 02 9627 8666 or text 0440 130 098 for details.
Delivery Australia Wide
BYD Shark 6 canopies ship Australia wide. Contact us for delivery estimates.
Have questions?
How much payload does the BYD Shark 6 have for a canopy?
Can I use V2L power with a canopy?
Is aluminium or steel better for a Shark 6 canopy?
Can I drill into the Shark 6 tub for canopy mounting?
Can I fit a roof top tent on a Shark 6 canopy?
What size is the BYD Shark 6 tub?
Is the Shark 6 suitable for a full touring build?
Can you install a canopy on my BYD Shark 6?
Need help choosing?
Call us on 02 9627 8666 or chat with our team.


