Collection: Bonnet Protectors

Tinted black bonnet guards moulded to the nose of popular utes and the Pajero Sport, from the PX2 Ranger and RG D-MAX to the MV Triton, D27 Navara and facelifted HiLux. Each one fits without drilling and takes gravel strikes before your paint does.

Showing products for your

Showing 10 of 10 results

Gear up for adventure
Gear up for adventure
Limited time sale

Gear up for adventure

Save big on canopies, racks, drawers & morethis season

What a Bonnet Guard Is For

A bonnet protector is a shaped strip of tinted plastic that runs across the nose of the bonnet and stands a little proud of the panel. At highway speed it bends the passing air upward, so grit, insects and small stones riding that airstream are more likely to skip over the panel than hit it head on. Whatever still arrives lands on the guard. Replacing a scuffed guard is a small job, whereas a peppered bonnet edge means paintwork, and a chip that reaches bare steel can let corrosion creep in under the surrounding paint.

Some of the lifted debris clears the windscreen as well. Be realistic, though: no guard can promise a chip free screen when you are sitting behind a loaded tipper or passing road trains, so treat glass protection as a bonus rather than the reason to buy.

How These Guards Are Made

Every guard in this collection is injection moulded from UV stabilised plastic with a black tint, which helps it resist fading, warping and cracking after years parked outside. Its profile is taken from a full laser scan of the vehicle, so it follows the curves of one particular bonnet rather than a generic shape. A complete fitting kit comes in the box and nothing needs drilling, which leaves the bonnet itself unmodified if you sell the ute or change your mind.

Fitment Follows the Bonnet Pressing

Because a guard hugs one specific panel, it is only as interchangeable as the bonnet underneath. When a manufacturer redraws the nose, even partway through a generation, a new guard has to follow. The listings in this range show how often that happens:

  • Ford Ranger: one guard for PX2 and PX3 Rangers and Raptors built 2015 to 07/2022, and a separate one for the RA Next Gen from 2022. Compare both in our Ranger bonnet guard collection.
  • Isuzu D-MAX: the RG is split in two, with a guard for 08/2020 to 04/2024 builds and another for the facelifted bonnet from 04/2024. See the guards made for the D-MAX.
  • Mitsubishi Triton: an MR guard from 2018 and an MV guard for the all new body from 2024, both listed under Triton bonnet protection. The QF Pajero Sport from 2020 has its own guard too.
  • Nissan Navara: the facelifted D23 from 01/2021 to 03/2026 takes one guard, and the D27 from 03/2026 takes another.
  • Toyota HiLux: one guard for the facelifted N80 built from 2020 to 07/2024.

Check the Build Month Before Ordering

Changeover months are where most wrong orders happen. A Ranger built in mid 2022, a D-MAX from around April 2024 or a Navara from early 2026 could sit on either side of a split. Go by the build month on the vehicle's compliance label, usually found in a door jamb or under the bonnet, rather than the date the ute was delivered or registered. If the label is hard to read, a clear photo of the front of your bonnet is usually enough for our team to confirm which guard you need.

Care That Keeps It Looking Right

Wash the guard whenever you wash the ute, using the same car shampoo and a soft mitt. Skip solvent cleaners, cutting compounds and machine polishers on the tinted plastic, as they can haze or scratch the surface. Every few washes, run a gentle stream of water behind the guard to flush out trapped grit and dead insects, since grit sitting between guard and paint can slowly wear through the clear coat. In the first weeks after fitting, check that the guard still sits evenly along its length, and have it looked at if you notice any rattle or movement at speed.

Insect remains are worth a mention. Left to bake on in summer, they can mark clear coat, and the guard takes a fair share of that mess, which is far easier to scrub off plastic than off paint.

Who Benefits Most

Utes that cover regional gravel, run behind trucks on major highways or head inland during harvest, when insect strikes are constant, get the most from a guard. Weekday city utes still collect chips on freeways and through roadworks, and a guard is one of the simplest ways to keep the front edge of a newer vehicle sharp for trade in time. It also pairs well with the rest of the front end range in protection and accessories.

Fitting at South Windsor

A careful home fit is straightforward with the kit and the supplier's fitting video: clean the bonnet edge thoroughly, test the position before committing and follow the instructions in order. If you would rather leave the alignment to someone else, NSW customers can have a guard fitted at our South Windsor showroom, on its own or alongside other work.

Call us on 02 9627 8666, text 0440 130 098, or visit our showroom at 20 Walker Street, South Windsor NSW 2756.

Have questions?

Will a bonnet protector stop my windscreen from chipping?

It reduces the debris reaching the glass by lifting airflow over the front of the vehicle, but it cannot block every stone, especially from trucks or oncoming traffic. Its main job is protecting the bonnet's front edge.

Do I need to drill holes in my bonnet?

No. Each guard comes with a full fitting kit and is a no drill install, so the panel stays as the factory made it.

Will the guard fade or crack in the sun?

The guards are moulded from UV stabilised plastic made to resist fading, warping and cracking, which suits vehicles that live outdoors.

My bonnet already has a few chips. Should I fix them first?

Yes. A guard protects against new damage but will not repair existing chips. Touching them up before fitting stops moisture getting under the paint in a spot that will be harder to inspect later.

Can I move my guard to my next ute?

Only if the next vehicle has the same bonnet. A guard from a PX3 Ranger will not suit a Next Gen, and an MR Triton guard will not suit an MV.

Is there a bonnet protector for the Pajero Sport?

Yes. There is a guard for the QF Pajero Sport from 2020, shaped for its own bonnet rather than the Triton's.

Need help choosing?

Call us on 02 9627 8666 or chat with our team.