BYD Shark 6 Tub Dimensions: Exact Measurements for Canopy and Accessory Fitment
The factory BYD Shark 6 pickup tub measures approximately 1,520 mm long, 1,500 mm wide and 517 mm deep, with…
Table of contents
The factory BYD Shark 6 pickup tub measures approximately 1,520 mm long, 1,500 mm wide and 517 mm deep, with a published capacity of 1,200 L. The width between the wheel arches at floor level is approximately 1,224 mm.
Those five numbers control canopy fitment, drawer width, fridge slide placement, roller shutter compatibility, hard lid clearance, pallet loading and how much room remains for a touring or tradie storage build.
Published specifications are a starting point. The factory spray in liner, wheel arch contours, V2L outlet covers, tub capping and canopy mounting hardware can all reduce the usable space inside an Australian delivered vehicle. Always measure the actual lined tub before ordering anything built to close tolerances.
BYD Shark 6 tub dimensions at a glance
| Measurement | Dimension | Source | Fitment relevance |
| Internal tub length | 1,520 mm | BYD published | Drawers, long cargo, sleeping systems |
| Maximum internal width | 1,500 mm | BYD published | Canopy shell and upper level storage planning |
| Tub depth | 517 mm | BYD published | Drawer height, fridge access, shutter clearance |
| Width between wheel arches | ~1,224 mm | OzCanopies fitment measurement* | Floor level drawer and pallet fitment |
| Published tub capacity | 1,200 L | BYD Australia specification sheet | General cargo volume comparison |
*The between wheel arches figure is a physical fitment measurement. Confirm against your actual vehicle and liner before ordering close tolerance products.
Imperial conversions (approximate)
| Metric | Imperial |
| 1,520 mm | ~59.8 in |
| 1,500 mm | ~59.1 in |
| 517 mm | ~20.4 in |
| 1,224 mm | ~48.2 in |
What each Shark 6 tub measurement actually means
Tub length: 1,520 mm
This is the approximate internal bed length, used when assessing drawer system length, fridge slide travel, long toolboxes, sleeping platforms, storage modules and motorcycle or bicycle fitment.
Usable floor length may be slightly less than 1,520 mm due to the front wall shape, liner thickness, tailgate closure profile, canopy mounting brackets at the front and the V2L outlet housing on the driver side.
Maximum tub width: 1,500 mm
This is the wider internal measurement above or around the wheel arch area. It should not be treated as the available width for a floor mounted drawer system. The wheel arches intrude below the tub rail, narrowing the floor. Drawers, fridge slides and storage systems that sit on the floor need to work within the narrower between arches dimension.
Common mistake: Ordering a drawer system based on the 1,500 mm maximum tub width. The floor is only approximately 1,224 mm wide between the arches. A 1,400 mm wide drawer set will not fit at floor level.
Tub depth: 517 mm
Use this for planning drawer deck height, roller shutter canister clearance, fridge height and lid access, canopy side window position and how far cargo can sit below the tub rail. The 517 mm depth is deeper than many competing utes (the Ford Ranger PHEV sits at approximately 498 mm), which gives Shark 6 owners a slight advantage for below rail concealment and drawer height.
Between wheel arches: approximately 1,224 mm
This is the most important floor level dimension for anyone planning drawers, a fridge and drawer layout, storage boxes, pallets, slide out kitchens or custom fabricated frames. The BYD Shark 6 fridge and drawer setup guide uses this figure as the primary design constraint for all floor level storage planning.
The 1,224 mm width is wide enough for both a standard Australian pallet (1,165 × 1,165 mm) and a Euro pallet (1,200 × 800 mm), which is a genuine advantage for tradies.
Does an Australian pallet fit in the Shark 6 tub?
A standard Australian pallet measures 1,165 × 1,165 mm. Using the approximately 1,224 mm measured width between the wheel arches, the nominal clearance is approximately 59 mm total (roughly 29 mm per side).
Important qualifications:
The usable clearance can be reduced by liner thickness, moulded wheel arch contours, tie down points, canopy mounting brackets, pallet manufacturing tolerances, load deformation and the angle required to load the pallet from the tailgate.
The published and measured dimensions indicate that a standard Australian pallet can fit between the wheel arches, but actual clearance should be confirmed on the vehicle before relying on regular pallet loading. Dimensional fit does not confirm that a particular pallet load is within the vehicle’s payload or axle limits. The BYD Shark 6 payload and GVM guide covers payload calculations in detail.
How the factory tub liner affects usable dimensions
Published dimensions describe the tub structure, not the lined interior
The specification sheet dimensions should not automatically be treated as the clear usable space after the liner, moulded ribs, wheel arch covers, upper tub rail capping, outlet covers and tie down hardware are accounted for.
The reduction is not uniform
The liner can reduce space differently at the front wall, floor ribs, wheel arches, lower corners, tailgate opening and the top rail. Do not assume a single universal figure like “the liner removes 10 mm from every side.” Measure the actual vehicle.
Measure to the nearest obstruction
For drawer or fridge slide fitment, measure between the closest wheel arch or liner points, not the widest visible part of the tub. For a canopy, measure and inspect the top rail width, capping profile, front and rear corner shape, sports bar mounting points and whether liner or capping is trapped beneath canopy mounts.
A drawer system can be several millimetres narrower than the available width and still work perfectly. A system built several millimetres too wide will not fit at all.
Which Shark 6 variants use these tub dimensions?
Premium pickup
Uses the factory pickup tub covered by this guide. BYD Australia’s specification sheet lists 1,200 L tub capacity for the Premium.
Performance pickup
Uses the same factory pickup tub. Tub dimensions and capacity are identical to the Premium. The Performance has a higher kerb weight (2,775 kg vs 2,710 kg), which affects payload but not tub size.
Dynamic Cab Chassis
Does not use the factory pickup tub. The Dynamic is a cab chassis variant requiring a separately fitted tray or service body. Usable tray dimensions depend on the tray manufacturer, tray width and length, headboard design, under tray storage and wheel and body clearance. BYD’s current Australian specification sheet lists tub capacity as not applicable for the Dynamic. Do not use this article’s measurements for a Dynamic Cab Chassis build.
Measurements needed for canopy fitment
Length, width and depth alone are not enough to confirm canopy compatibility. A fitter should also check tub rail length, front and rear rail width, rail capping thickness, corner radii, front wall shape, cab to tub gap, distance from rail to cab roofline, sports bar mounting holes, tailgate opening and hinge movement, high mounted brake light visibility, V2L outlet locations, tub lights, tie down points and canopy clamp or bolt access.
A canopy described as “approximately the right size” is not necessarily Shark 6 specific. A proper vehicle specific fitment should account for the tub profile, mounting structure, sealing surface, electrical integration, tailgate operation and body movement. The BYD Shark 6 clamp on vs bolt on canopy mounting guide covers the mounting method differences and their effect on fitment.
Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney to confirm fitment measurements for your specific Shark 6.
Measurements needed for drawers and fridge slides
Start from the narrowest floor width
Use the actual measured space between the lined wheel arches, not the published 1,500 mm top of tub width.
Subtract all fixed components
Account for fridge slide frame width, drawer frame walls, centre dividers, side clearances, cable channels, bolt heads, canopy mounting brackets and protective carpet or lining.
Planning formula:
Available drawer width = measured usable width minus fridge slide width minus mounting clearances
Check length and extension
Confirm that the drawer frame fits against the front wall, drawer handles clear the tailgate, fridge slide extends beyond the tailgate, fridge lid can open under the canopy roof and electrical cables remain clear of runners during slide movement.
Measurements needed for roller shutters and hard lids
For a roller shutter, check the tub rail profile, internal width at the canister location, sports bar compatibility, tailgate clearance, drain hose routing, V2L and light access, clamp location and liner or capping interference. A roller shutter canister normally occupies space near the front of the tub, reducing usable tub length by 100 to 200 mm.
For a hard lid, check cargo height clearance, fridge access, sports bar compatibility, future canopy conversion options and access to tall equipment. The BYD Shark 6 canopy vs hard lid vs roller shutter comparison covers the trade offs between all tub cover types.
How to measure your Shark 6 tub correctly
Step 1: Empty and clean the tub
Remove loose mats, boxes and anything that prevents the tape measure sitting correctly against the surfaces.
Step 2: Confirm what will remain fitted
Measure with the actual liner, capping, V2L outlets and sports bar hardware that will remain after installation.
Step 3: Measure floor length
Measure from the nearest point of the front wall or liner to the closed tailgate contact area. Record the shortest figure.
Step 4: Measure between the wheel arches
Take measurements at the front, centre and rear of the tub floor. Use the narrowest figure. This is the dimension that controls drawer and fridge slide fitment.
Step 5: Measure upper width
Check the top, middle and lower portions because the tub is not a perfect rectangle. The upper width is wider than the floor.
Step 6: Measure depth and opening height
Record floor to tub rail, floor to canopy roof (if already fitted), tailgate opening height and side access opening dimensions (if a canopy with gullwing doors is fitted).
Step 7: Photograph and record obstructions
Document the locations of V2L outlets, tub lights, tie down points, canopy brackets, drain holes and liner ribs. These affect where drawers, fridge slides and wiring can sit.
Measure twice, record the narrowest result and allow installation tolerance rather than designing to a zero clearance fit.
What we recommend at Oz Canopies & 4×4: Bring your Shark 6 to the showroom and we will measure it with you. A five minute tape measure session with the actual vehicle is worth more than an hour of guessing from a spec sheet. Browse the Shark 6 canopy and accessory range to see what fits.
Common measurement mistakes
- Using the 1,500 mm maximum width for floor level drawers (the floor is approximately 1,224 mm)
- Ignoring the factory spray in liner when calculating usable space
- Measuring with the tailgate open only (check clearance when closed too)
- Assuming the tub is perfectly square (it is not)
- Measuring at only one point between the arches (measure front, centre and rear)
- Forgetting that canopy mounting brackets consume space at the tub rail
- Blocking V2L outlet covers with drawers or shelving
- Ordering a fridge by internal capacity rather than checking its external dimensions
- Forgetting the fridge slide frame width when calculating remaining drawer space
- Allowing no fitting tolerance (a few millimetres of clearance prevents a jammed install)
- Assuming Premium dimensions also apply to a Dynamic Cab Chassis tray
- Confusing tub dimensions with overall vehicle dimensions
- Assuming dimensional fit confirms legal payload capacity
Quick fitment checklist
- < > Shark 6 variant confirmed (Premium, Performance or Dynamic)
- < > Factory tub or aftermarket tray confirmed
- < > Floor length measured (from front wall to tailgate contact)
- < > Width between arches measured at three points (use narrowest)
- < > Upper tub width measured
- < > Tub depth measured (floor to rail)
- < > Tailgate opening width and height checked
- < > Liner and rail capping thickness included in measurements
- < > V2L outlets located and access confirmed
- < > Tub lights and tie down points located
- < > Canopy bracket positions checked (if applicable)
- < > Fridge external dimensions confirmed
- < > Drawer and slide clearances allowed
- < > Roof height and sports bar compatibility checked
- < > Final measurements supplied to installer or manufacturer
FAQs
How long is the BYD Shark 6 tub?
How wide is the Shark 6 tub?
How deep is the Shark 6 tub?
Does an Australian pallet fit in the Shark 6?
Does the factory liner reduce the usable tub width?
Are Premium and Performance tub dimensions the same?
Does the Dynamic Cab Chassis have the same tub?
Should I measure the tub before ordering a canopy?
Your next step: measure, then order
Use the published dimensions to shortlist accessories. Then measure the actual lined tub before ordering anything built to close tolerances. The difference between a smooth install and a frustrating return is often 5 mm.
For the full picture of how tub dimensions fit into a complete Shark 6 canopy build, including payload maths, electrics, storage layouts and recommended packages, the BYD Shark 6 canopy and tub setup guide ties everything together.
Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney to get your Shark 6 measured for canopy and accessory fitment.