How to Set Up a Fridge and Drawer System in a BYD Shark 6 Canopy
A fridge and drawer system turns a canopy from a lockable box into a functional camp kitchen, mobile workshop or…
Table of contents
A fridge and drawer system turns a canopy from a lockable box into a functional camp kitchen, mobile workshop or touring storage platform. But getting the layout right on a Shark 6 means designing around one number most owners overlook: 1,224 mm.
That is the usable width between the rear wheel arches at floor level. The tub is 1,500 mm wide at the top, which sounds generous. But the fridge, slide and drawer system all sit down on the floor and 1,224 mm is the real space they have to share. Once you subtract the fridge slide width, installation clearances, liner thickness and manufacturing tolerances, the remaining width for drawers is tighter than most people expect.
This guide walks through the layout decisions in the right order: choose the fridge first, choose its position and slide type, calculate the remaining drawer width, plan the weight distribution and design the mounting and restraint system so everything stays put when the road gets rough.
Quick answer: what layout works best for most Shark 6 owners?
A good all round starting point
For most touring builds, the default layout is:
- Fridge on one side, drawer bank on the other
- Approximately one third to half of the available floor width for the fridge and slide
- The remaining width for one wide drawer or two narrower drawers
- Heavy recovery gear in the lowest drawer
- Battery and electrical equipment low and close to the front of the tub
- Lighter camping equipment above or toward the rear
- Clear access to the Shark 6’s factory tub V2L outlets
- Fridge slide extending fully beyond the tailgate or canopy rear opening
The critical rule is: choose the fridge and complete layout first, then order the drawer system. Do not buy a generic full width drawer unit and try to squeeze the fridge in afterwards.
Common mistake: Buying a drawer system based on the “1,500 mm tub width” catalogue figure, then discovering the drawers are too wide for the 1,224 mm floor and need to be returned or modified. Always design to the floor width, not the top of tub width.
Measure the Shark 6 before ordering anything
Start with the correct floor dimension
The published Shark 6 tub measurements are:
- Tub length: approximately 1,520 mm
- Width at the top: approximately 1,500 mm
- Width between wheel arches (floor level): 1,224 mm
- Tub depth: approximately 517 mm
The 1,224 mm floor width is the relevant starting point for any low mounted drawer and fridge system.
Measure your actual vehicle
Published dimensions are a starting point. Before ordering anything, measure:
- Usable width between wheel arches (confirm with a tape measure)
- Wheel arch intrusion (how far the arches protrude into the tub)
- Factory spray in liner thickness at the floor and arches
- Canopy base bracket locations (these can eat floor width)
- Tailgate opening width
- Canopy rear door opening height and width
- Side access window or door dimensions
- Distance from floor to canopy roof interior
- Tub V2L outlet and wiring locations
Allow installation tolerance
Do not design a system at exactly 1,224 mm. Allow room for:
- Liner thickness variation
- Drawer frame manufacturing tolerances
- Bolt heads and bracket flanges
- Wiring runs alongside the drawers
- Carpet or protective trim
- Movement during installation
- Removal and servicing later
A 10 to 20 mm total clearance allowance is sensible. Tight is fine. Jammed is not.
Choose the fridge before designing the drawers
Record the fridge’s real external dimensions
Before choosing a drawer system, know the fridge’s actual footprint:
- External width
- External depth
- Closed height (with feet, handles and any protrusions)
- Open lid height (with the lid fully open)
- Handle and latch projections
- Power plug clearance at the rear or side
- Ventilation clearance requirements (from the manufacturer)
- Loaded weight (fridge plus a realistic amount of food and drinks)
Add the fridge slide dimensions
The slide can be wider and longer than the fridge itself. Record:
- Slide frame external width (including mounting flanges)
- Locking handle projection
- Travel length (how far the slide extends)
- Load rating
- Slide mechanism height (standard, drop or tilt)
- Total weight of the slide
Test lid clearance before committing
A fridge that technically fits in the canopy can still be unusable if its lid hits the canopy roof, the slide cannot clear the tailgate or shelving above prevents the lid from opening.
Check whether the lid can open fully with:
- The slide fully extended
- The tailgate lowered
- The canopy rear door open
- Any shelving installed above the fridge position
- An internal roof light, switch panel or electrical panel nearby
Common mistake: Choosing a fridge based on internal capacity and price without checking its external dimensions against the canopy. A 60 L fridge with a wide body can consume more floor width than a 50 L fridge with a slimmer profile. External dimensions matter more than litres.
Fridge on the left or right: which side is better?
Fridge on the passenger side
Potential advantages:
- Easier kerbside access when parked on Australian roads (passenger side faces the kerb)
- Convenient for roadside stops and fuel station snack grabs
- May suit campsites where the passenger side faces the living area
- Can leave the driver side free for tools, batteries or electrical equipment
Potential disadvantages:
- May conflict with an awning side kitchen layout if the awning is also on the passenger side
- Battery or wiring location may require longer cable runs
- Access depends on how the canopy doors are configured
Fridge on the driver side
Potential advantages:
- May place the fridge closer to the battery and electrical components
- Can suit layouts where the driver side canopy door is used more frequently
- Keeps the passenger side clear for camp kitchen or awning setup
Potential disadvantages:
- Roadside access is less convenient in Australia (driver side faces traffic)
- The layout must preserve access to the Shark 6’s factory tub V2L outlets on the driver side
- Side to side weight distribution must still be considered
The real answer
There is no universal winner. Choose the side based on:
- Canopy door configuration (which side opens and how)
- Camp kitchen and awning position
- Fridge cable run to the battery and fuse box
- Battery and fuse box placement
- Whether the driver side tub V2L outlets need to remain accessible
- Where other heavy equipment will sit (balance left and right)
- Whether the vehicle normally parks level at camp
Passenger side placement often works well for casual access. But the best Shark 6 layout is the one that balances access, electrical routing and weight across the vehicle.
How wide should the drawer system be?
Work backwards from the available floor width
Use this planning formula:
Available drawer width = usable floor width minus fridge slide width minus installation clearances
Start from the actual measured floor width, not the catalogue figure alone.
Example planning exercise
Here is a clearly labelled hypothetical example:
| Item | Width (mm) |
| Measured usable floor width | 1,210 |
| Fridge and slide assembly (external) | 560 |
| Centre gap and side clearances | 30 |
| Remaining drawer bank width | ~620 mm |
Actual fridge and slide dimensions will vary by brand and model. Run this calculation with your specific fridge.
One wide drawer vs two narrow drawers
One wide drawer: Suits bulky items like cookware, recovery straps and large tool cases. Fewer runners and dividers. Can become very heavy when fully loaded.
Two narrower drawers: Better organisation (separate food from tools from recovery gear). May weigh more because of extra framing and runner sets. Very narrow drawers can waste usable width.
Do not forget wheel arch height
A raised drawer deck can extend above the wheel arches and use more width. But it also raises the fridge, adds structural weight, increases the lift height for loading and may require a drop or tilt slide to bring the fridge back to a comfortable access height.
Standard slide, drop slide or tilt slide?
Standard fridge slide
Best when the fridge sits low, access height is comfortable, simplicity and lower weight matter and there is enough room for the lid to open without hitting the canopy roof.
Drop slide
Best when the drawer deck raises the fridge significantly and shorter users need easier access. A drop slide lowers the fridge as it extends, bringing it to a more practical working height.
Trade offs: more weight, greater cost, more moving parts and more space required behind and below the mechanism.
Tilt slide
Best where the fridge is only slightly too high and a full drop mechanism is unnecessary. A tilt slide angles the fridge forward as it extends, improving lid access without the complexity of a full drop.
Remember that the slide’s own weight and load rating count toward the Shark 6’s overall vehicle payload.
Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney to compare fridge slides and drawer systems for the Shark 6.
Weight distribution: where the heavy equipment should go
This is where the fridge and drawer layout connects directly to the Shark 6’s payload story. The BYD Shark 6 payload and GVM guide covers the full weight calculation, but here are the principles that matter for storage layout.
Keep heavy equipment low
Heavy items include: a loaded fridge (25 to 45 kg), an auxiliary battery (12 to 20 kg), tools, recovery gear, water (20 L = 20 kg) and compressors. Place them on or near the tub floor to keep the vehicle’s centre of gravity as low as practical. This improves handling, braking and off road stability.
Keep fixed weight forward where practical
Avoid placing every heavy component against the tailgate. Positioning fixed weight closer to the front of the tub reduces rear heavy loading, which matters even more when towing. The tub’s V2L outlets and any battery system should ideally sit toward the front wall of the canopy.
Balance left and right
If the loaded fridge sits on one side, consider placing the battery, water or heavy tools on the opposite side. Do not treat side to side balance as an excuse to put very heavy equipment high or far rearward. Low and balanced is the goal.
Include loaded weights, not empty weights
The weight calculation must include the fridge plus a realistic food and drink load (not an empty fridge), drawers plus their full contents, the slide mechanism, battery, water, the canopy itself, passengers, recovery equipment and towball download where applicable. The Shark 6’s standard 790 kg payload can disappear quickly once the vehicle is accessorised.
Common mistake: Calculating the weight of the drawer system empty, not loaded. An empty double drawer weighs 40 to 55 kg. Fill it with tools, recovery gear, cookware and a first aid kit and it can easily double.
How to secure the drawer system properly
A heavy drawer system cannot rely on its own weight
The National Transport Commission’s Load Restraint Guide for Light Vehicles specifically notes that both light and heavy loads can move if they are not properly restrained. A restraint system must account for braking, cornering, acceleration and corrugated roads.
Create a proper load path
The installation should transfer force through:
Drawer frame → rated brackets and fasteners → suitable vehicle or tub mounting structure
Do not rely only on thin canopy flooring, self tapping screws, carpet, adhesive, friction or unverified liner material.
Use rated hardware and mounting points
- Manufacturer approved brackets designed for the drawer system
- Appropriate high tensile fasteners
- Spreader plates where required (to distribute load on thin panels)
- Locking nuts or thread locking compound where specified
- Corrosion protection for any drilled holes
Because the Shark 6 is a PHEV, drilling through the tub or body should only occur after confirming what wiring, lines and structural components are below the proposed mounting location. The BYD Shark 6 clamp on vs bolt on canopy mounting guide covers the broader principles of drilling, sealing and warranty considerations.
NTC restraint performance standards
The current NTC light vehicle guide describes minimum restraint forces equivalent to:
- 80% of the load’s weight forwards (braking)
- 50% sideways (cornering)
- 50% rearwards (acceleration or impact)
- 20% upwards where the load is not fully contained
These are the baseline the complete mounting and restraint system needs to address. They are not a DIY bolt size calculator. Transport for NSW and equivalent state authorities enforce load restraint requirements at roadside inspections and an inadequately restrained drawer system in a canopy is treated the same as an unsecured load on a tray. If you are unsure whether your mounting design meets these standards, talk to a qualified fitter.
Securing the fridge to the slide
The fridge must remain attached to the slide
Use manufacturer approved mounting feet, rated fridge straps or locking brackets designed for the fridge model. Ordinary elastic straps or loose ropes are not sufficient restraint for a 30 to 45 kg loaded fridge during heavy braking or a corrugation hit.
The slide must lock closed
Confirm that the locking mechanism engages fully, the fridge cannot slide forward during braking, the slide cannot unlatch on corrugations and handles and latches remain accessible for inspection.
Secure the contents too
A restrained drawer cabinet does not automatically restrain everything stored on top of it. Use tie down rails, cargo barriers, rated straps, enclosed boxes or locking fridge barriers for loose items above the drawer deck. The NTC Load Restraint Guide applies to everything in the canopy, not just the big items.
Fridge ventilation and heat management
Leave room around the vents
Compressor fridges need airflow to reject heat. Do not box the fridge tightly between a drawer wall, canopy sidewall, battery box, electrical panel or stored bedding. Check the manufacturer’s minimum clearance requirements (typically 50 to 100 mm on the compressor side and rear).
Do not place heat producing components beside the fridge
Avoid crowding the fridge compressor with a DC DC charger, inverter, second compressor or an unventilated battery enclosure. Heat from neighbouring components forces the fridge to work harder, drawing more power and reducing its efficiency.
Consider the canopy environment
A dark canopy sitting in direct sun can become extremely hot inside. Ventilation paths (side windows, door airflow or a positive pressure vent) help reduce internal temperatures. A reflective or insulated fridge cover can also help. Keeping the canopy sealed for dust protection is covered in the BYD Shark 6 canopy dustproofing guide, but ventilation for fridge cooling is a separate consideration that may require compromise.
Plan the fridge wiring before mounting the drawers
Use a dedicated fused circuit
The fridge should run from the auxiliary battery on a dedicated, individually fused circuit with correctly sized cable and a secure connection (locking outlet or hardwired connector). The BYD Shark 6 canopy electrical wiring guide covers circuit design, fuse sizing and cable gauge in detail.
Avoid long, undersized plug in extensions
Voltage drop over a long, thin cable can cause fridge compressor cut outs even when the battery still has charge. Keep the fridge cable run as short as practical and use the correct gauge for the amperage and run length.
Keep wiring serviceable
Plan the cable route before the drawers go in. The fuse box must remain accessible (not buried behind the drawer frame). The fridge power plug must be reachable when the slide is retracted. Cable strain relief must prevent the slide mechanism from pulling or pinching wires during extension and retraction.
Preserve the Shark 6’s factory power access
Make sure the drawers, fridge enclosure and side panels do not permanently obstruct the tub’s factory V2L outlets. The three 230 V outlets sit under a flap on the driver side and blocking them eliminates one of the Shark 6’s biggest advantages. The BYD Shark 6 V2L power guide explains how to use those outlets alongside a 12 V auxiliary system.
Step by step installation process
Step 1: List everything the system must carry. Fridge, food, cookware, recovery gear, tools, water, electrical equipment and camping boxes. Write it all down with weights.
Step 2: Measure the tub and canopy openings. Record all usable dimensions with a tape measure rather than relying only on published figures.
Step 3: Choose the fridge location. Confirm left or right side, tailgate clearance, canopy door access, lid opening height, power route and ventilation path.
Step 4: Design the drawer footprint. Work backwards from the fridge and slide assembly width. Allow 10 to 20 mm total installation clearance.
Step 5: Create a weight budget. Record empty and loaded weights for the canopy, drawers, fridge, battery, water and gear. Compare the total against the Shark 6’s available payload.
Step 6: Confirm mounting points. Have the drawer manufacturer or fitter identify attachment points, bracket design, hardware, spreader plate requirements and drilling locations. Confirm what is below any proposed drill point.
Step 7: Install and wire the system. Fit the structural system first. Route protected wiring without placing cables near runners, sharp edges or pinch points.
Step 8: Load and test. Check drawer locks, slide lock, fridge lid clearance, tailgate clearance, rattles, cable movement during slide operation and handling under braking.
Step 9: Recheck after the first trip. Inspect all mounting bolts, drawer runners, fridge straps and electrical connections after the system has settled. Corrugated roads will test every fastener.
Three example Shark 6 layouts
Weekend touring layout
- 40 to 50 L fridge on a standard slide (passenger side)
- One drawer bank (~600 mm wide) on the driver side
- Basic canopy lighting and USB off a small auxiliary battery
- Removable camping boxes above the drawers
- Minimal fixed weight. Light enough for standard GVM.
Remote touring layout
- 50 to 60 L fridge on a drop or tilt slide
- Twin drawers (one for food and cooking, one for recovery and tools)
- 100 Ah lithium battery with DC DC charger, mounted low near the front wall
- 20 to 40 L water storage (jerry cans or compact tank)
- Recovery gear in the lowest drawer
- Tie down rail above the drawer deck for loose items
- Heavier build. May benefit from a GVM upgrade if towing is also planned.
Work and weekend layout
- Removable fridge slide or fridge module (quick release for workdays)
- Tool drawers with dividers for fasteners, hand tools and power tool batteries
- Open cargo deck above the drawers for materials and bulky loads
- Quick release camping boxes that swap in for weekends
- No permanent water system. V2L handles worksite power.
What we recommend at Oz Canopies & 4×4: Start with the weekend touring layout if you are new to canopy builds. It is the simplest to install, the lightest on payload and easy to upgrade later. Add the battery, water and extra drawers once you know what your actual camping style demands. Browse the BYD Shark 6 canopy options to see which canopies suit a drawer and fridge fitout.
Common fridge and drawer setup mistakes
- Buying drawers before choosing the fridge (the fridge determines the remaining width)
- Designing to the full 1,224 mm with no tolerance (everything jams)
- Forgetting the width of the slide frame and mounting flanges
- Raising the fridge too high on a tall drawer deck without a drop slide
- Failing to check lid clearance against the canopy roof or shelving
- Placing all heavy equipment behind the rear axle
- Mounting fridge, battery and water on the same side (unbalanced)
- Blocking the Shark 6’s driver side V2L outlet flap
- Burying the fuse box behind the drawer frame where it cannot be reached
- Relying on self tapping screws as the primary drawer mount
- Failing to restrain cargo stored above the drawers
- Calculating empty rather than loaded weights
- Not rechecking fasteners after corrugated roads
Shark 6 fridge and drawer planning checklist
- < > Actual floor width between wheel arches measured
- < > Fridge external dimensions confirmed (width, depth, height, lid open height)
- < > Loaded fridge weight recorded (fridge plus food and drinks)
- < > Slide width and weight recorded
- < > Lid opening height checked against canopy roof
- < > Tailgate clearance checked with slide fully extended
- < > Canopy door clearance checked
- < > Left or right fridge placement chosen
- < > Drawer bank width calculated (floor width minus fridge/slide minus clearances)
- < > Installation tolerance allowed (10 to 20 mm)
- < > Battery and electrical placement planned (low, forward, accessible)
- < > V2L outlet access preserved on the driver side
- < > Fridge ventilation clearance checked against manufacturer specs
- < > Fixed and trip load weight calculated against available payload
- < > Drawer frame mounting method confirmed with rated hardware
- < > Fridge restraint system confirmed (straps, brackets or locking feet)
- < > Cargo tie down points included above the drawer deck
- < > Fuse box location remains accessible after installation
- < > First trip bolt and fastener inspection scheduled
FAQs
How wide is the Shark 6 tub floor between the wheel arches?
What width drawer system fits a BYD Shark 6?
Should the fridge go on the driver or passenger side?
How should a drawer system be restrained?
Does a drawer system count toward payload?
Can the drawers block the Shark 6 V2L outlets?
Should heavy recovery gear go in the bottom drawer?
How often should drawer mounting bolts be checked?
Your next step: design the layout, then order the parts
The right order of decisions for a Shark 6 fridge and drawer setup is:
- Choose the fridge
- Choose its side and slide type
- Measure the remaining drawer width
- Calculate the complete loaded weight
- Design the structural mounting and restraint
- Plan wiring and ventilation
- Only then order the drawer system
A good Shark 6 storage system is not the one with the most drawers. It is the one that keeps the fridge accessible, uses the 1,224 mm floor intelligently, distributes weight properly and keeps every component restrained when the road gets rough.
For the full picture of how the storage layout fits into a complete Shark 6 canopy build, including payload maths, electrics, roof loads and three complete build packages, the BYD Shark 6 canopy and tub setup guide ties everything together.
Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney to plan your Shark 6 fridge and drawer layout.