BYD Shark 6 V2L Power Guide: How to Use Your Tub Outlets for Work and Camping

The Shark 6 is not just another ute with a 12 V cigarette lighter socket. It comes from the factory…

By Chris 25 min read Published Last updated:

BYD Shark 6 V2L Power Guide: How to Use Your Tub Outlets for Work and Camping
Table of contents

The Shark 6 is not just another ute with a 12 V cigarette lighter socket. It comes from the factory with four 230 V household style power outlets (three in the tub, one in the rear cabin) that can deliver up to 6.6 kW combined. That is enough to run power tools on a remote worksite, power a campsite without a generator or even keep the lights on at home during a blackout.

But here is the part most articles skip: factory V2L is brilliant for portable AC devices and short term convenience. It is not a replacement for a properly planned 12 V auxiliary system if you want a permanently running fridge, hardwired canopy lighting, solar input or dedicated touring circuits.

This guide covers what the factory outlets can actually power, how the V2L system works (including the settings most owners never touch), when V2L is enough on its own and when you still need a proper 12 V canopy electrical system built around a DC DC charger and auxiliary battery. If you have already read the electrical section in the main BYD Shark 6 canopy guide, this goes deeper.

Key Shark 6 power specs

Spec Detail
Tub V2L outlets 3 × 230 V, 10 A (under flap, driver’s side)
Rear cabin V2L outlet 1 × 230 V, 10 A
Combined V2L output Up to 6.6 kW (tub outlets)
Cabin V2L output Up to 2.2 kW
12 V accessory socket Under 10 A / under 120 W, ignition on only
V2L discharge floor Do not let battery drop below 15%
Default discharge timer 5 hours (adjustable through infotainment)
SOC management Target SOC, AUTO and SAVE modes available
Battery capacity 29.58 kWh (LFP)

Before you plug anything in: 3 point check

  1. Know what type of load you are connecting. AC appliances (power tools, kettles, chargers) go on V2L outlets. DC accessories (fridge, LED lights, water pump) belong on a 12 V system.
  2. Check your battery state of charge. The handbook says not to discharge below 15%. Set a minimum SOC through the infotainment before you start using V2L at camp or on site.
  3. Know your discharge time. The default V2L session is 5 hours. If you need longer, adjust it through the infotainment settings before you start.

Quick answer: what can the Shark 6 power from the factory?

What you get from factory

The Shark 6 comes with four V2L (Vehicle to Load) outlets:

  • Three in the tub: Located under a weather protected flap on the driver’s side. Standard Australian 230 V three pin sockets, each rated at 10 A. Combined output up to 6.6 kW.
  • One in the rear cabin: Behind the front seats. 230 V, 10 A. Output up to 2.2 kW.

You also get a conventional 12 V accessory socket in the centre console area. This is a standard cigarette lighter style outlet, not a V2L outlet.

What V2L is best for

  • Charging power tool batteries on site
  • Running corded power tools (drills, grinders, small circular saws)
  • Powering camping lights, phone chargers, laptops
  • Running a kettle, coffee machine or portable induction cooktop at camp
  • Charging camera batteries, drones and portable devices
  • Running a portable 230 V fridge for short trips
  • Emergency home power during a blackout (with appropriate setup)

The honest answer

Factory V2L gives the Shark 6 a massive head start over any diesel ute. No generator needed on site. No separate power pack for camping. Just plug in and go.

But V2L is AC power from the vehicle’s drive battery. It is not a dedicated 12 V auxiliary system. If you want a permanently running compressor fridge, hardwired LED canopy lights, a water pump, USB outlets, solar charging input or battery monitoring, you still need a proper 12 V canopy electrical system. V2L and 12 V are different tools for different jobs. The rest of this article helps you work out which one you need or whether you need both.

Shark 6 power outlets explained: V2L vs 12 V

Rear cabin and tub V2L outlets

The V2L outlets deliver 230 V AC power, the same voltage as a household wall socket. The power comes from the Shark 6’s 29.58 kWh lithium iron phosphate (LFP) battery through the vehicle’s built in inverter.

The tub outlets are the primary V2L access point for most owners. They sit under a flap on the driver’s side of the tub, protected from weather when closed. The rear cabin outlet is handy for charging laptops or running small appliances inside the vehicle.

Key points:

  • V2L is only available when the system is activated through the infotainment (or when certain conditions are met at the chargeport).
  • The vehicle can be locked while V2L is running from the tub outlets.
  • V2L draws from the same battery that powers the vehicle’s electric motors. Heavy or prolonged use reduces your driving range.

The 12 V accessory socket is not your canopy power system

The Shark 6 has a standard 12 V accessory socket in the cabin. The handbook says this outlet is for accessories drawing less than 10 A and less than 120 W and it is only available when the ignition is on.

That is enough for a phone charger or a small tyre inflator. It is not enough for a fridge, LED strip lights, a water pump or any combination of 12 V accessories you would run in a canopy.

Common mistake: Assuming the 12 V cigarette lighter socket can power a canopy fridge. It cannot. The socket is rated under 120 W, the fridge draws more than that on startup and the socket only works with the ignition on. If you run a fridge overnight, you need a dedicated 12 V system with its own battery.

Which loads belong where

Load type Best power source Why
Power tools (corded) V2L (tub outlets) AC power, high draw, short duration
Battery chargers (tool, phone, laptop) V2L (cabin or tub) AC power, moderate draw
Kettle, coffee machine, toaster V2L (tub) AC power, high draw, short duration
Portable 230 V fridge (short trip) V2L (tub) AC power, moderate draw, monitor SOC
12 V compressor fridge (permanent) Auxiliary battery (12 V) Runs 24/7, needs stable DC power
LED canopy lights Auxiliary battery (12 V) Low draw, hardwired, always available
Water pump Auxiliary battery (12 V) DC motor, intermittent use
USB charging (canopy) Auxiliary battery (12 V) Hardwired USB outlets in canopy
Solar panel input Auxiliary battery (via regulator) DC charging, needs battery controller
Compressor (tyre inflation) V2L or 12 V Depends on compressor type

How V2L actually works on the Shark 6

Starting and controlling V2L

To activate V2L on the Shark 6:

  1. Connect your device or power board to one of the V2L outlets.
  2. Open the infotainment system and navigate to Energy > Charging and Discharging.
  3. Toggle Vehicle To Load on.

V2L requires the discharge connector (your device) to be connected before you toggle the system on. The vehicle needs to be in Park with the electronic parking brake engaged.

Once activated, the V2L indicator appears on the instrument cluster and power flows to the outlets.

Default discharge timer

Here is a detail most Shark 6 owners do not know about: the default V2L discharge duration is 5 hours. After 5 hours, the system shuts off automatically.

If you need a longer (or shorter) session, you can adjust this through the infotainment: tap the Settings button on the V2L screen to change the single discharge time.

For a workday on site, 5 hours might not be enough. For an overnight camp fridge run, it definitely is not. Adjust the timer before you leave the cab or you will wake up to a warm fridge and flat beers.

Common mistake: Setting up a portable fridge on V2L at camp and leaving the default 5 hour timer running. The fridge powers down at 2 AM and everything defrosts. Adjust the discharge duration or use a dedicated 12 V system for overnight fridge runs.

Low battery behaviour

The handbook is clear: do not let the vehicle’s battery drop below 15% when using V2L.

If the battery reaches a low state of charge (SOC) while V2L is running:

  • With ignition off: You can enable an option through the infotainment that allows the petrol engine to start automatically and generate electricity when SOC gets too low. The engine runs as a generator to keep power flowing.
  • With ignition on: The vehicle can automatically start the engine to generate electricity without needing to pre set anything.

This means the Shark 6 can technically run V2L indefinitely (as long as there is fuel in the tank and the engine generator option is enabled). But running the petrol engine at camp to keep V2L alive defeats some of the purpose of having a PHEV. It also creates noise and emissions at your campsite.

For short duration, high draw needs (worksite tools, cooking, charging), V2L with SOC management is perfect. For long duration, low draw needs (fridge overnight, canopy lights all evening), a dedicated 12 V auxiliary battery is the cleaner solution.

Target SOC, AUTO mode and SAVE mode: the settings Shark 6 owners should actually understand

These settings live in the Shark 6’s infotainment system under the Energy screens. Most owners never touch them. That is a mistake, because they directly affect how much battery power you have available for V2L at camp or on site.

What target SOC means

Target SOC (State of Charge) is the battery level the vehicle aims to maintain while driving. You can set it by sliding down the infotainment status bar to access the shortcut page or through the Energy screen.

Think of it as a “reserve level” instruction to the hybrid system. If you set target SOC to 50%, the vehicle will try to keep the battery at or near 50% while driving by using the petrol engine to generate electricity when the battery drops below that level.

When to run a lower target SOC

The handbook recommends a lower target SOC when your destination has convenient charging available. This maximises electric driving and reduces fuel consumption. Good for daily commuting where you charge overnight at home.

When to run a higher target SOC

The handbook recommends a higher target SOC when your destination does not have convenient charging. This is the critical setting for camping, worksite and remote use.

If you are driving to a campsite and plan to use V2L when you arrive, set a higher target SOC before you leave. That way, you arrive with a fuller battery and more V2L runtime. If you leave it on a low setting, you might arrive at camp with 25% battery and very limited V2L capacity.

Practical example: You are driving 200 km to a bush camp. Set target SOC to 70%. The hybrid system will maintain at least 70% battery while driving. When you arrive, you have roughly 70% of 29.58 kWh available for V2L, which is about 20 kWh of usable energy. That runs a 50 W camp fridge for days or a 2,000 W kettle for several hours.

AUTO vs SAVE mode

Two driving modes affect how the hybrid system manages battery power:

  • AUTO: Prefers fuel economy while also considering battery power keeping. The system balances petrol and electric use for the best overall efficiency. Good for daily driving.
  • SAVE: Prefers keeping vehicle battery power and tries to stay close to the target SOC. The petrol engine does more of the work to preserve battery charge. Use this when you want to arrive at your destination with a full battery for V2L.

The camping move: Set target SOC to 70% and switch to SAVE mode on the drive to camp. Arrive with a healthy battery. Switch to V2L when you get there. This is the single most useful V2L strategy for Shark 6 tourers.

Common mistake: Driving to a remote campsite in AUTO mode with a low target SOC, arriving with 20% battery and then wondering why V2L only runs the campsite for an hour before hitting the 15% floor. Plan your SOC before you leave, not when you arrive.

What can you realistically run from Shark 6 V2L?

Good worksite uses

  • Battery chargers: Power tool batteries (Makita, DeWalt, Milwaukee) charge happily from V2L. Multiple chargers simultaneously is fine within the 6.6 kW combined limit.
  • Corded drills and grinders: Most corded drills draw 500–1,000 W. Angle grinders draw 700–2,000 W. Both work on V2L, but check the wattage rating before plugging in.
  • Circular saws: Most draw 1,200–2,000 W. Fine on V2L as a single load. Do not run a circular saw and a grinder at the same time.
  • Small compressors: Portable air compressors for nail guns or tyre inflation (typically 1,000–1,500 W) run well on V2L.
  • Laptops and site electronics: Minimal draw. Run as many as you like.
  • LED work lights: Very low draw. Perfect V2L application.

Good camping uses

  • Camp lighting: LED string lights, lanterns and floodlights. Negligible draw.
  • Coffee machine: A typical pod machine draws 1,000–1,400 W. Runs fine on V2L for the 2–3 minutes it takes to make a coffee.
  • Portable induction cooktop: Most single burner induction cooktops draw 1,000–2,000 W. Usable on V2L for cooking sessions, but monitor your SOC.
  • Portable 230 V fridge: Works for short trips if you manage the discharge timer and SOC. Not ideal for multi day trips because it relies on the drive battery.
  • Phone, camera and drone charging: Minimal draw. V2L handles this effortlessly.
  • Electric blanket: 50–200 W. Perfectly fine for cold weather camping.

Loads that deserve caution

  • High startup appliances: Some compressors and power tools have a startup surge that exceeds their running wattage. If a tool keeps tripping the V2L, the startup draw is likely too high.
  • Devices running unattended for hours: Anything you plug in and walk away from (heaters, slow cookers, dehumidifiers) will drain the battery steadily. Monitor SOC or set a discharge timer.
  • Hair dryers and fan heaters: These draw 1,500–2,400 W continuously. They work, but they chew through battery fast.
  • Gear better served by 12 V: If something runs 24/7 (fridge, canopy lights, water pump), hardwire it into a 12 V system instead of running it off a V2L outlet with an AC to DC converter. Less efficient, more points of failure and you are using the drive battery unnecessarily.

When factory V2L is enough and when you still need a real 12 V canopy system

This is the most commercially useful section in the article. Get this decision right and you save money, weight and complexity.

Factory V2L is enough if you:

  • Camp casually (1–2 nights, powered or semi powered sites)
  • Need occasional worksite power for tools and chargers
  • Do day trips where you plug in a few devices and head home
  • Do not want to install any permanent electrical system
  • Are happy managing SOC and discharge timers manually
  • Run a portable 230 V fridge that you unplug when driving

For these use cases, V2L is genuinely all you need. No auxiliary battery. No DC DC charger. No wiring. Just plug in and go.

You still need a proper 12 V system if you want:

  • A permanently running compressor fridge (12 V, runs 24/7 including while driving)
  • Hardwired LED canopy lighting on a switch panel
  • A 12 V water pump for a canopy mounted water tank
  • USB outlets permanently wired into the canopy
  • Solar panel input for extended off grid camping
  • Battery monitoring (SOC gauge, voltage display)
  • A compressor on a dedicated circuit
  • Multi day camping without relying on the drive battery or running the engine

V2L gives the Shark 6 a huge head start. But it does not eliminate the need for a proper auxiliary system if your use case is serious touring rather than convenience power.

What we recommend at Oz Canopies & 4×4: Most Shark 6 owners doing weekend camping with a canopy can get away with V2L for appliances and a basic 12 V circuit (100 Ah lithium battery, DC DC charger, fused distribution) for the fridge and lights. That combination covers 90% of use cases without overbuilding.

The 3 tier Shark 6 power system

This is the framework we use when helping Shark 6 owners plan their electrical builds. Pick the tier that matches how you actually use the ute.

Tier 1: Factory V2L only

Best for: Simple campers, occasional site power, owners who do not want to install anything.

Component Purpose
Factory V2L outlets (tub + cabin) AC power for tools, chargers, cooking
Portable power board (if needed) Expand outlet count
SOC management (target SOC + SAVE mode) Arrive at camp with a full battery
Discharge timer adjustment Extend or limit V2L sessions

Cost: $0 (already fitted). Maybe $30 for a quality power board.

Limitations: No 12 V accessories. No permanent fridge. No canopy lighting. No solar. No overnight fridge runs without engine generator backup.

Tier 2: V2L + basic 12 V canopy circuit

Best for: Fridge users, touring weekenders, canopy lighting and USB, moderate camping.

Component Purpose
100 Ah slimline lithium battery Dedicated 12 V power for fridge, lights, USB
25 A DC DC charger Charges auxiliary battery from vehicle 12 V while driving
6 way fused distribution panel Circuit protection for all 12 V loads
LED canopy light strips (2) Canopy interior lighting
USB outlets (2) Canopy charging points
12 V compressor fridge circuit Dedicated fridge power
V2L (factory) AC power for cooking, tools, charging

Cost: $1,500–$3,500 depending on battery brand and installation.

Why this works on the Shark 6: V2L handles all your AC needs (tools, cooking, charging). The 12 V system handles the always on, overnight and hardwired needs (fridge, lights, pump). Each system does what it does best.

Tier 3: Full touring electrical setup

Best for: Remote touring, extended camping, solar dependent setups, serious basecamp builds.

Component Purpose
200 Ah lithium battery (or 2 × 100 Ah) Extended 12 V power for multi day trips
40 A DC DC charger Faster auxiliary charging while driving
200–400 W fixed solar panels (canopy roof) Off grid charging at camp
Solar regulator/MPPT controller Manages solar input to battery
Battery monitor (Victron, Renogy, etc.) Real time SOC and voltage tracking
8 way fused distribution panel Full circuit protection
LED lighting, USB, fridge, water pump circuits All hardwired 12 V loads
Compressor circuit (tyre inflation) Dedicated air supply
2,000 W pure sine inverter (optional) 230 V AC from the auxiliary battery, independent of V2L
V2L (factory) High draw AC tools, cooking, rapid charging

Cost: $4,000–$8,000+ depending on components and installation.

Why the inverter is optional: On the Shark 6, V2L already provides 230 V AC from the factory. You only need an inverter on the auxiliary battery if you specifically want 230 V AC power independent of the drive battery (e.g., running a CPAP machine overnight without touching the Shark’s main battery).

DC DC chargers, fuse boxes and proper wiring: where good Shark 6 builds separate from messy ones

Why a DC DC charger still matters in a PHEV ute

Even with excellent factory V2L, a dedicated auxiliary battery system still needs correct charging. A DC DC charger takes power from the vehicle’s 12 V system while driving and steps it up to the correct voltage to charge a lithium auxiliary battery safely.

Without a DC DC charger, your auxiliary battery only charges from solar (if fitted) or from a mains charger when you are at home. That means long drives do nothing for your camping battery, which is a waste.

A quality DC DC charger (Redarc, Enerdrive, Renogy) ensures your auxiliary battery is topped up every time you drive. On the Shark 6, this works the same as on any other ute. The DC DC charger connects to the vehicle’s 12 V system, not the high voltage PHEV battery.

Mounting and cable run principles

  • Mount the DC DC charger close to the auxiliary battery. Ideally within about 1 metre for best performance. Shorter cable runs mean less voltage drop and more efficient charging.
  • Keep the charger away from heat sources. DC DC chargers generate heat during charging. Mount them where airflow is adequate, not buried under drawers or sealed in a cupboard.
  • Run cables through conduit or loom protection. Any cable passing through the tub, canopy or chassis should be protected from chafing, vibration and water.
  • Separate 12 V and 230 V wiring. Keep AC (V2L extension leads) and DC (auxiliary battery circuits) physically separated to avoid interference and reduce fire risk.

Fuse protection and cable sizing

Every circuit in your 12 V system needs a fuse matched to the wire it protects. The fuse is there to protect the wire from overheating, not to protect the appliance. If the wire is rated for 15 A, the fuse should be 15 A or less.

Wire gauge selection depends on two factors: the amperage of the load and the voltage drop over the cable run length. Longer runs need thicker wire to avoid excessive voltage drop, which can cause dim lights, slow fridge startups and wasted energy.

A qualified auto electrician will size your wiring correctly. If you are doing a DIY install, use a wire gauge chart or calculator and err on the side of thicker wire.

Common mistake: Running all canopy accessories off a single unfused cable from the vehicle battery. One short circuit and you have a fire risk. Every circuit needs its own fuse and every cable needs to be rated for the load it carries. This is non negotiable. The NTC Load Restraint Guide covers securing cargo, but electrical safety is equally critical for a touring build. Australian wiring standards (AS/NZS 3000 for general wiring principles) provide the framework.

Best canopy electrical layouts for Shark 6 owners

Worksite setup

You need to charge tool batteries, run corded tools occasionally and have some light inside the canopy for early morning starts.

  • V2L outlets: Handle all tool charging and corded power tool use. No changes needed.
  • 12 V canopy circuit: A small 12 V fuse box (4 way), a pair of LED strip lights and a feed from the vehicle’s 12 V system powers the lights. No auxiliary battery needed for this setup.
  • Total added weight: Under 5 kg for the 12 V lighting circuit.

Weekend camping setup

You want a fridge running overnight, canopy lights, USB charging and the ability to cook with a kettle or induction cooktop at camp.

  • V2L outlets: Handle cooking (kettle, cooktop), phone/laptop charging and any other AC appliances.
  • 12 V canopy circuit: 100 Ah lithium battery, 25 A DC DC charger, 6 way fuse box. Dedicated circuits for fridge, LED lights, USB outlets and a water pump.
  • Solar (optional): A portable 120 W panel for extended stops, connected to the auxiliary battery via a regulator.
  • Total added weight: 15–25 kg for the battery, charger, fuse box and wiring.

Touring setup

You need full self sufficiency for multi day remote trips. Fridge, lights, pump, compressor, solar and monitoring.

  • V2L outlets: Reserved for high draw cooking, power tools and occasional 230 V appliances. Not used for daily camp operation.
  • 12 V canopy circuit: 200 Ah lithium battery, 40 A DC DC charger, 8 way fuse box, battery monitor. Dedicated circuits for fridge, lights, USB, water pump and compressor.
  • Solar: 200–400 W fixed panels on the canopy roof, connected via MPPT controller.
  • Inverter (optional): Only if you need 230 V AC from the auxiliary battery independent of V2L (e.g., medical devices overnight).
  • Total added weight: 30–50 kg for the full electrical system.

Safety, limits and mistakes to avoid

Do not treat V2L like an endless power source

The Shark 6’s V2L runs from the same 29.58 kWh battery that powers the vehicle’s electric motors. The handbook says not to discharge below 15%. If you drain the battery too far, you lose electric driving range and the vehicle may need the petrol engine to start and generate power.

Use the target SOC and SAVE mode settings to protect your battery. Set a floor before you start using V2L and check it periodically.

Do not overload the 12 V socket

The handbook is explicit: the 12 V accessory socket is rated for accessories under 10 A and under 120 W total. It only works with the ignition on. Do not use it as a canopy distribution system. It is a convenience socket for phone chargers and small electronics, nothing more.

Do not build a messy hybrid system

The most common electrical mistakes we see on Shark 6 builds:

  • Mixing AC and DC gear without a plan. V2L provides 230 V AC. Canopy accessories run on 12 V DC. If you are running a 230 V fridge off V2L and 12 V lights off an auxiliary battery, you have two completely separate systems that need to be managed independently. Plan this upfront.
  • No fuse protection. Every 12 V circuit needs a fuse. Full stop.
  • Undersized cable. Thin wires get hot under load. Use the correct gauge for the amperage and run length.
  • Using the console 12 V outlet for canopy accessories. This kills the fuse or melts the wiring. Run a proper feed from the auxiliary battery.
  • No SOC planning before arriving at camp. If you drive to camp in AUTO mode with a low target SOC, you arrive with a nearly flat battery and minimal V2L capacity. Set target SOC high and use SAVE mode on the drive in.

Buying guide: what to ask before paying for a Shark 6 electrical setup

Before you hand over money for an electrical fitout, ask these questions:

  1. Do I actually need an auxiliary battery or is factory V2L enough? If your use case is casual camping or occasional worksite power, V2L alone might be all you need. Do not overbuild.
  2. What loads will be permanent vs portable? Permanent loads (fridge, lights, pump) need 12 V hardwiring. Portable loads (tools, chargers, cooking) can stay on V2L.
  3. Where will the DC DC charger be mounted? It should be close to the auxiliary battery with adequate airflow. Inside a sealed drawer is not ideal.
  4. How will fuse protection be laid out? Every circuit should have its own fuse on a distribution panel. Ask to see the fuse box layout before the install starts.
  5. What cable gauge is being used and why? Your installer should be able to explain the gauge choice for each circuit based on amperage and run length.
  6. Is the layout designed around fridge runtime, not just peak power? A fridge running overnight draws a modest but continuous load. The system needs to support 10–12 hours of fridge operation without going flat.
  7. Will I be relying on V2L or 12 V circuits for camping essentials? The answer should be clear for each device. If the installer cannot tell you, find a different installer.

What we recommend at Oz Canopies & 4×4: Talk to us before you commit to an electrical package. We will help you work out which tier matches your actual use case and we will make sure the build is clean, fused and properly integrated with your BYD Shark 6 canopy. Call 02 9627 8666 or text 0440 130 098.

Recommended Shark 6 electrical packages

V2L only weekender package

Who it is for: Casual campers, day trippers, tradies who need occasional site power.

What it powers: Tools, chargers, camp cooking, phone/laptop.

Components: Factory V2L outlets only. Add a quality 4 way power board for the tub and a short heavy duty extension lead.

Why it works on the Shark 6: You already have 6.6 kW of AC power in the tub. For simple use, there is nothing to install.

Cost: $0–$50.

V2L + fridge and light package

Who it is for: Weekend tourers with a canopy, fridge users, moderate campers.

What it powers: Fridge (12 V, overnight), canopy LED lights, USB outlets, plus V2L for cooking and charging.

Components: 100 Ah lithium battery, 25 A DC DC charger, 6 way fuse box, LED lights, USB outlets, fridge circuit wiring.

Where V2L ends and 12 V begins: V2L handles cooking, charging and all AC appliances. The 12 V system handles the fridge, lights and USB, running independently of the drive battery.

Cost: $1,500–$3,500 installed.

Full touring power package

Who it is for: Remote tourers, extended campers, solar dependent builds.

What it powers: Everything. Fridge, lights, pump, compressor, USB, solar, monitoring, plus V2L for tools and cooking.

Components: 200 Ah lithium battery, 40 A DC DC charger, MPPT solar controller, 200+ W fixed solar, 8 way fuse box, battery monitor, all canopy circuits.

Where V2L ends and 12 V begins: V2L is reserved for high draw, short duration AC loads (power tools, kettle, induction cooktop). The 12 V system runs all camp essentials independently, charged by solar and DC DC while driving.

Cost: $4,000–$8,000+ installed.

FAQs

How many V2L outlets does the BYD Shark 6 have?

Four. Three 230 V outlets in the tub (under a flap on the driver’s side) and one 230 V outlet in the rear cabin.

Are the Shark 6 tub outlets 230 V?

Yes. All V2L outlets are standard Australian 230 V, 10 A three pin sockets. The three tub outlets can deliver up to 6.6 kW combined. The cabin outlet can deliver up to 2.2 kW.

Does the Shark 6 also have a cabin power outlet?

Yes. One V2L outlet in the rear cabin (230 V, 10 A) and a conventional 12 V accessory socket in the centre console (under 120 W, ignition on only).

Can I run camping gear from the Shark 6 tub outlets?

Yes. Lights, chargers, a kettle, a coffee machine and portable appliances all work well. For short trips, you can even run a portable 230 V fridge. For multi day trips, a dedicated 12 V fridge system is more reliable.

What is the 12 V socket limit in the Shark 6?

Under 10 A and under 120 W total draw. The 12 V socket is only active when the ignition is on. It is not designed for high draw or permanent accessories.

Can I use the 12 V socket with the ignition off?

No. The handbook states the 12 V auxiliary power is only available when the ignition is on.

What battery level should I keep before using V2L?

Do not discharge below 15%. For best results, set a target SOC of 50–70% before driving to your destination and use SAVE mode to arrive with a full battery.

How do I turn V2L on in the Shark 6?

Connect your device to a V2L outlet, then navigate to Energy > Charging and Discharging on the infotainment screen and toggle Vehicle To Load on. The vehicle must be in Park with the electronic parking brake engaged.

What is the default V2L discharge duration?

5 hours. You can adjust this through the infotainment settings on the V2L screen.

What does SAVE mode do?

SAVE mode prioritises keeping the vehicle’s battery charged. It runs the petrol engine more to preserve battery SOC, so you arrive at your destination with more battery power available for V2L. Use SAVE mode on the drive to camp if you plan to use V2L when you get there.

Do I still need a dual battery style setup in a Shark 6?

It depends on your use case. If you want a permanently running 12 V fridge, hardwired canopy lights, USB outlets, solar input or a water pump, yes, you need an auxiliary battery and DC DC charger. V2L handles AC appliances brilliantly, but it does not replace a dedicated 12 V canopy electrical system for always on DC loads.

Where should a DC DC charger be mounted?

Close to the auxiliary battery (ideally within 1 metre) for best charging efficiency. Mount it where airflow is adequate, away from direct heat sources. Not buried under drawers or sealed in a cupboard.

Your next step: match your power system to how you actually use the ute

Here is the fastest way to pick your power tier:

  1. Do you only need power tools and chargers at camp or on site? Tier 1 (V2L only). You are already sorted from the factory.
  2. Do you want a fridge running overnight and canopy lights on a switch? Tier 2 (V2L + basic 12 V). Add a 100 Ah lithium, DC DC and a fused distribution panel.
  3. Do you want full self sufficiency for multi day remote trips? Tier 3 (full touring setup). Add a 200 Ah lithium, DC DC, solar, battery monitor and all hardwired canopy circuits.

Not sure which tier fits? Drop into the Oz Canopies & 4×4 showroom at 20 Walker St, South Windsor, call 02 9627 8666 or text 0440 130 098. We will match the electrical system to your canopy build, your camping style and your budget.

Browse our full range of BYD Shark 6 accessories online.