BYD Shark 6 Payload & GVM Guide: Weight Maths Every Owner Needs
Most Shark 6 owners will not exceed their payload because of one big, obvious item. They will exceed it because…
Table of contents
Most Shark 6 owners will not exceed their payload because of one big, obvious item. They will exceed it because of lots of perfectly normal items added together. A canopy. A set of drawers. A fridge. A roof rack. An awning. Recovery gear. Twenty litres of water. Two adults. A dog. And then someone hitches up a trailer with 200 kg of ball weight and wonders why the rear is sitting low.
The Shark 6 has a nominal payload of approximately 790 kg. That sounds workable. It is workable, if you understand where every kilogram goes and plan accordingly. But 790 kg disappears faster than most people expect once the ute stops being stock.
This guide walks through the real payload maths, shows you three worked examples that make the numbers concrete, explains when a GVM upgrade genuinely makes sense and gives you a practical framework for managing weight so you stay legal, safe and comfortable. For more details visit out BYD Shark 6 Canopy & Tub Setup Guide.
Key Shark 6 weight specs
| Spec | Figure |
| Kerb weight | 2,710 kg |
| GVM (Gross Vehicle Mass) | 3,500 kg |
| Nominal payload | ~790 kg |
| Front axle load (at max allowable total mass) | 1,595 kg |
| Rear axle load (at max allowable total mass) | 1,905 kg |
| Occupant capacity | 5 |
| GVM with Ironman 4×4 upgrade | 3,850 kg |
| Payload with Ironman 4×4 upgrade | ~1,140 kg |
| Braked towing capacity | 2,500 kg |
| Max towball download | 250 kg |
Before you load anything: 3 point check
- Know your starting number. The Shark 6’s nominal payload is approximately 790 kg. That is all you have to work with before a GVM upgrade.
- Know what counts. Payload includes everything you add to the vehicle: people, accessories, cargo and towball download. Not just the stuff in the tub.
- Know your individual vehicle. Kerb weight can vary slightly depending on options and fluids. If you are close to the limit, weigh the actual vehicle at a public weighbridge, not the brochure number.
Quick answer: what is the BYD Shark 6 payload?
The official starting numbers
BYD publishes the following for the Australian market Shark 6 Premium:
- Kerb weight: 2,710 kg
- GVM: 3,500 kg
- Derived payload: 3,500 minus 2,710 = 790 kg
That 790 kg is the maximum weight you can legally add to the vehicle, full stop.
Why that number is only the beginning
The brochure payload is not “cargo capacity.” It is the total allowance for everything added to the vehicle beyond its factory kerb weight. That includes:
- The driver (budget 75–100 kg)
- Every passenger (75–100 kg each, up to 4 more)
- Aftermarket accessories (canopy, drawers, roof rack, bull bar, awning, batteries, fridge slide)
- Cargo in the tub or canopy (tools, camping gear, luggage, recovery equipment, water)
- Roof mounted gear (rooftop tent, rack accessories, solar panels)
- Towball download if towing (up to 250 kg)
Every one of those items comes out of the same 790 kg budget.
The honest answer
790 kg is workable. It is not generous. On a diesel HiLux or Ranger with ~950–1,050 kg of payload, you have more breathing room. On the Shark 6, the PHEV powertrain (battery, motors, control systems) adds kerb weight that diesel utes do not carry, which narrows the gap between kerb and GVM.
That does not make the Shark 6 a bad ute. It makes it a ute that rewards owners who do their weight homework before they start buying accessories.
What kerb weight, GVM and payload actually mean
Kerb weight
Kerb weight is what the vehicle weighs as it rolls off the production line with all standard equipment, a full tank of fuel and all fluids topped up, but no occupants, no aftermarket accessories and no cargo.
For the Shark 6: 2,710 kg. That includes the 29.58 kWh LFP battery pack, both electric motors, the 1.5 litre petrol engine, the spray in tub liner and all factory fitted equipment.
GVM (Gross Vehicle Mass)
GVM is the maximum allowable total mass of the vehicle, fully loaded. This is a legal limit set by the manufacturer and stamped on the compliance plate. You must not exceed it.
For the Shark 6: 3,500 kg.
Exceeding GVM is an offence in all Australian states and territories. It can also void your insurance, damage the vehicle’s suspension and braking systems and create a serious safety risk for you and other road users.
Payload
Payload is the gap between kerb weight and GVM. It is not a separate rating. It is a derived number.
3,500 kg (GVM) minus 2,710 kg (kerb) = 790 kg (payload)
Think of it as a budget. You start with 790 kg and every person, accessory and piece of cargo you add spends from that budget. When it hits zero, you are at GVM. Go beyond that and you are overloaded.
Common mistake: Treating the 790 kg payload as “tub capacity” or “how much stuff I can put in the back.” It is the total weight you can add anywhere on the vehicle, including inside the cab, on the roof, in the tub, on the towbar and on any aftermarket bull bar, rack or canopy.
Axle loads matter too
Even when your total vehicle weight is under GVM, you need to think about how the weight is distributed between the front and rear axles.
The Shark 6 handbook lists:
- Front axle load (at max allowable total mass): 1,595 kg
- Rear axle load (at max allowable total mass): 1,905 kg
These are the maximum loads each axle can handle at GVM. If you stack all your weight at the back of the vehicle (heavy canopy, drawers, water, tools and towball load all behind the rear axle), you can exceed the rear axle limit even if your total GVM is fine. You can also unload the front axle to the point where steering response suffers.
Axle load distribution is not something most owners check, but it matters for handling, braking and tyre wear, especially when towing.
The payload maths most owners forget
The simple formula
Here is the formula that governs every Shark 6 build:
Available payload = GVM (3,500 kg) minus kerb weight (2,710 kg) minus people minus fixed accessories minus trip cargo minus towball download
Or more simply:
Available cargo/towing headroom = 790 kg minus people minus all accessories
Every item on the vehicle subtracts from that number. When the number reaches zero, you are at GVM.
Why accessories count just as much as cargo
Most owners think about payload in terms of “what I put in the tub.” But permanent accessories are payload too and they sit on the vehicle every single day:
| Accessory | Typical weight (kg) |
| Aluminium canopy | 60–95 |
| Steel canopy | 100–140 |
| Bull bar (aluminium) | 25–40 |
| Bull bar (steel) | 40–65 |
| Drawer system (single) | 20–35 |
| Drawer system (double) | 35–55 |
| Roof rack / platform + legs | 15–25 |
| Awning (2.0–2.5 m, packed) | 15–25 |
| Rooftop tent (folded) | 40–70 |
| 100 Ah lithium battery + DC DC charger | 15–20 |
| Fridge slide + fridge (50 L, empty) | 30–45 |
| Towbar (aftermarket) | 15–30 |
| Side steps (pair) | 10–20 |
A typical tradie build (aluminium canopy, drawers, bull bar, roof rack, side steps) can hit 180–260 kg before any tools or people are on the vehicle. A touring build (canopy, drawers, fridge, battery, awning, roof rack) can hit 200–310 kg.
That is a quarter to a third of your entire payload budget consumed by accessories alone.
Common mistake: Pricing and planning a canopy build based on features and fit, without ever adding up the total weight of every accessory in the package. Then loading the ute with tools, two passengers and a trailer and being 100 kg over GVM without realising it.
Why towball mass changes everything
If you tow, the towball download (vertical load) counts as payload. The Shark 6’s maximum towball download is 250 kg.
Adding 200–250 kg of ball weight to a vehicle that is already carrying a canopy build, two adults and gear can push you right to or past, the GVM limit. This is covered in detail in BYD Shark 6 Towing Capacity & Setup Guide, but the short version is: towball download and payload come from the same budget. You cannot ignore one while spending the other.
BYD Shark 6 payload calculator: how to work it out properly
Step 1: Start with 790 kg
That is your budget. Write it down. Everything else gets subtracted from it.
Step 2: Subtract people first
Most payload calculators start with accessories. Start with people instead, because people are on the vehicle every trip.
| Occupants | Weight estimate (kg) |
| Driver only | 90 |
| Driver + 1 passenger | 170 |
| Driver + 2 passengers | 250 |
| Driver + 3 passengers | 330 |
| Driver + 4 passengers | 410 |
With a driver and one passenger, you are already at 170 kg used, leaving 620 kg. With five occupants, you have used 410 kg, leaving 380 kg for everything else.
Step 3: Subtract fixed accessories
Add up every aftermarket accessory permanently fitted to the vehicle. Use the table above as a guide, but always use the actual weight from the manufacturer, not a guess.
Step 4: Subtract trip specific load
This is the variable stuff: tools, recovery gear, water, luggage, camping supplies, firewood, dog, building materials, whatever you carry on a given day or trip.
Step 5: If towing, subtract towball download
The towball download from your loaded trailer comes off the same budget. If your trailer puts 200 kg on the ball, subtract 200 kg.
The worksheet
| Line | Item | Weight (kg) |
| A | Starting payload | 790 |
| B | People (driver + passengers) | ___ |
| C | Fixed accessories (canopy, drawers, rack, bar, etc.) | ___ |
| D | Trip cargo (tools, gear, water, luggage) | ___ |
| E | Towball download (if towing) | ___ |
| F | Remaining payload (A minus B minus C minus D minus E) | ___ |
If line F is negative, you are over GVM. If it is close to zero, you are at the limit. If it is under 50 kg, you have no meaningful margin for error.
3 payload budget examples every Shark 6 owner should see
Example 1: Tradie daily setup
| Item | Weight (kg) |
| Starting payload | 790 |
| Driver | 90 |
| Aluminium canopy | 85 |
| Drawer system (double) | 45 |
| Bull bar (aluminium) | 30 |
| Roof crossbars | 8 |
| Side steps | 15 |
| LED light bar | 3 |
| Tools and consumables in drawers | 80 |
| Loose materials in tub (daily average) | 50 |
| Total loaded | 506 kg |
| Remaining payload | 284 kg |
284 kg remaining. Add a passenger (90 kg) and you are at 194 kg. Start towing a plant trailer with 180 kg ball weight and you are at 14 kg remaining. That is technically legal but leaves zero margin.
Takeaway: A tradie who regularly tows with this setup is right at the edge. A GVM upgrade moves the ceiling and gives genuine breathing room.
Example 2: Touring weekender setup
| Item | Weight (kg) |
| Starting payload | 790 |
| Driver + passenger | 170 |
| Aluminium canopy | 85 |
| Single drawer system | 25 |
| Fridge slide + 50 L fridge (loaded) | 40 |
| 100 Ah lithium battery + DC DC | 15 |
| Awning (2.0 m, packed) | 18 |
| Roof rack + crossbars | 18 |
| Recovery gear (snatch strap, shackles, MaxTrax) | 15 |
| 40 L water (2 × 20 L jerry cans) | 40 |
| Camping gear (swag, chairs, kitchen box) | 40 |
| Total loaded | 466 kg |
| Remaining payload | 324 kg |
324 kg remaining. That is comfortable for a weekend away without towing. Add a rooftop tent (55 kg) and you drop to 269 kg. Add a small camper trailer with 120 kg ball weight and you are at 149 kg. Legal, but tight.
Takeaway: A touring weekender build works well on stock GVM for couples who are disciplined about weight. Add a rooftop tent and towing and you start needing the GVM upgrade.
Example 3: Towing focused setup
| Item | Weight (kg) |
| Starting payload | 790 |
| Driver + passenger | 170 |
| Hard lid (aluminium) | 55 |
| Basic tub organiser | 15 |
| Camping essentials (bags, cooler, chairs) | 30 |
| Towball download (caravan, 200 kg) | 200 |
| Total loaded | 470 kg |
| Remaining payload | 320 kg |
320 kg remaining. Looks fine. But add two rear passengers (160 kg) and you are at 160 kg. Now stack a full canopy build instead of a hard lid and you are deep into single digits.
Takeaway: If towing is a regular part of your life, keep the on vehicle build as light as possible. A hard lid instead of a canopy saves 30–40 kg. Fewer drawers saves 25 kg. Every kilogram you save on accessories is a kilogram available for ball weight and passengers.
Why the Shark 6’s payload gets tight faster than some owners expect
It is a PHEV ute with a 2,710 kg kerb weight
The Shark 6 carries a 29.58 kWh battery pack, two electric motors, a petrol engine and the associated power electronics. That is a lot of hardware and it pushes the kerb weight higher than a comparable diesel ute. A Ford Ranger XLT diesel starts around 2,200–2,300 kg kerb. A Toyota HiLux SR5 is similar. The Shark 6 is roughly 400–500 kg heavier before you add anything.
With the same 3,500 kg GVM as many diesel competitors, that higher kerb weight translates directly into less available payload. It is not a design flaw. It is the trade off for having a PHEV powertrain with instant torque, V2L power and significantly lower running costs.
Accessories add up faster than brochures suggest
When you browse a canopy catalogue, each accessory looks lightweight and reasonable on its own. A 85 kg canopy. A 45 kg drawer system. A 18 kg awning. A 30 kg fridge and slide.
Individually, they are fine. Together, they are 178 kg of permanent weight on the vehicle before you have put a single tool, camping chair or passenger on board. Add the driver and that is 268 kg gone from your 790 kg budget. That is a third of your payload consumed by the ute’s permanent setup.
This is why the brief in the main canopy pillar emphasises lightweight aluminium canopies over heavier fibreglass or steel. On the Shark 6, material choice is not just an aesthetics decision. It is a payload decision.
Touring and towing together are where the maths usually get ugly
The moment you combine a full canopy touring build with a towing setup (caravan, camper trailer, boat), the payload numbers compress from both ends. The canopy build eats payload from one side, the towball download eats it from the other and passengers sit in the middle wondering where their luggage allowance went.
This is not unique to the Shark 6. It happens on every ute. But the Shark 6’s tighter 790 kg starting point means you hit the wall sooner.
GVM upgrade for the BYD Shark 6: when does it make sense?
What Ironman 4×4 is currently advertising
Ironman 4×4 offers the first certified GVM upgrade for the Shark 6. The key numbers:
- GVM increased to: 3,850 kg (from 3,500 kg)
- Payload increased to: approximately 1,140 kg (an extra 350 kg)
- Front axle capacity: increased from 1,610 kg to 1,800 kg
- Rear axle capacity: increased from 1,954 kg to 2,150 kg
- Includes: IM2.5 monotube shock absorbers, matched springs, all GVM compliance components (CAT 6 indicators and wiring for NB1 class upgrade)
- Approximate lift: 30 mm
- Pricing: From $4,190 fitted through accredited Ironman 4×4 centres
- Kits available: Medium (occasional loads), Heavy (constant loads over 300 kg) and Extra Heavy (constant loads over 600 kg)
- Pre registration and post registration options available
The GVM upgrade process must comply with VSB 14, the national code of practice for light vehicle modifications, published by the Department of Infrastructure, Transport, Regional Development, Communications and the Arts. VSB 14 sets the technical requirements. State and territory transport authorities handle the administrative side and processes vary.
Who a GVM upgrade is actually for
A GVM upgrade makes genuine sense if:
- You are a tradie carrying a heavy canopy build plus tools every day and regularly picking up passengers or towing
- You are building a full touring setup (canopy, drawers, fridge, battery, water, awning, rooftop tent) and want legal headroom for the total build plus occupants
- You tow regularly with a loaded vehicle and the towball download plus accessories consistently push you close to 790 kg
- You run a fleet vehicle that needs to carry consistent loads within legal limits
Who probably does not need one
- Daily drivers with a stock or lightly accessorised Shark 6
- Occasional campers who manage weight carefully
- Owners who have never actually weighed their vehicle and are guessing they are overloaded
- Owners who would be better served by simplifying their build (lighter canopy, fewer drawers, less roof weight) rather than paying to raise the ceiling
Common mistake: Buying a GVM upgrade because you “might need it one day” without ever putting the actual vehicle on a weighbridge to see where you stand. Weigh first, upgrade second.
The important catch with GVM upgrades
Technical requirements and admin requirements are not the same
The Department of Infrastructure notes that VSB 14 covers the technical requirements for vehicle modifications, but does not cover the administrative requirements of each state and territory. Each state has its own processes for registering a modified GVM. What is straightforward in one state may require additional steps or different paperwork in another.
Before committing to a GVM upgrade, check with your local registration authority (RMS in NSW, VicRoads in Victoria, TMR in Queensland, etc.) to confirm the current process for your state.
Pre registration and post registration are not identical in practice
Ironman 4×4 offers both pre registration kits (for vehicles not yet registered) and post registration kits (for vehicles already on the road). Pre registration kits carry federally recognised approval. Post registration kits enable current owners to upgrade, but the process and requirements vary by state.
If you are buying a new Shark 6 and know you want the GVM upgrade, doing it pre registration is generally the simpler path. If your Shark 6 is already registered, check what your state requires before booking the install.
Bottom line
A GVM upgrade is a real, legitimate and valuable modification. But it is not a “just bolt it on” situation. The technical engineering is handled by Ironman’s certified kit. The administrative process is handled by your state or territory. Make sure both boxes are ticked.
Does a GVM upgrade solve everything?
More payload helps, but bad weight distribution can still be bad
Even with a 3,850 kg GVM and 1,140 kg of payload, you still need to distribute weight correctly between the front and rear axles. A vehicle loaded to 3,850 kg with everything stacked behind the rear axle will handle poorly, brake badly and wear rear tyres unevenly.
The upgraded axle capacities (1,800 kg front, 2,150 kg rear) give more room, but they do not eliminate the need for sensible loading. Heavy items low and forward. Light items high and rearward. Always.
Towing limits do not automatically increase
This is a critical point: the Ironman GVM upgrade raises GVM and payload, but it does not change the Shark 6’s braked towing capacity (still 2,500 kg) or the GCM (still 5,750 kg).
What it does do is give you more payload headroom while towing. On standard GVM, a loaded canopy build plus passengers plus 200 kg ball weight can leave you with under 100 kg of margin. On the upgraded GVM, the same scenario might leave you with 450 kg of margin. That is a massive difference for towing comfort and legality, even though the tow rating itself stays the same.
A GVM upgrade is not a substitute for doing the maths
The upgrade moves the ceiling. It does not remove the ceiling. You still need to add up people, accessories, cargo and ball weight. You still need to stay under 3,850 kg total. You still need to manage axle loads. The maths are just less stressful because you have 350 kg more to work with.
Best practice loading for Shark 6 owners
Keep heavy items low and forward
The lowest, most forward position in the canopy or tub is the best place for heavy items. This keeps the centre of gravity low and weight closer to the vehicle’s centre, which improves stability, braking and handling.
Batteries, water tanks and heavy toolboxes belong on the floor of the canopy, as far forward as the drawer system allows. Not on shelves, not on top of drawers and definitely not on the roof. The NTC Load Restraint Guide for Light Vehicles covers the principles of securing and distributing loads and while it is aimed at commercial operators, the same physics apply to every Shark 6 with a canopy.
Do not let rear heavy builds sneak up on you
The most common loading mistake is adding accessories and cargo progressively to the rear of the vehicle without thinking about cumulative effect. A heavy drawer system, a water tank, a fridge, recovery gear and a towball load all sit behind the rear axle line. Each one shifts the balance rearward.
Symptoms of a rear heavy build:
- Headlights pointing upward (blinding oncoming traffic)
- Light or vague steering feel
- Rear suspension sitting low or on bump stops
- Excessive tyre wear on the rears
- Nose diving under heavy braking (front axle is too light)
Weigh the vehicle properly, not by feel
You cannot tell whether you are over GVM by looking at the rear springs or “feeling” the ride. A vehicle can look fine and still be overloaded. The only way to know is to put it on a weighbridge.
Public weighbridges are available in most industrial areas and regional towns across Australia. Many are operated by local councils or private operators. A weigh costs $10–$30 and takes 5 minutes. It is the single most useful thing you can do before a long trip or after a major accessory install.
When to weigh your Shark 6
After major accessory installs
Fitted a canopy, drawers and a bull bar? Weigh the vehicle before you load anything else. This gives you your new baseline kerb weight (factory kerb plus permanent accessories) and lets you calculate your actual remaining payload accurately.
Before a big trip
Loaded up for a two week touring trip? Drive to the weighbridge on your way out of town. If you are over, you can rearrange or leave non essentials behind. Much better to find out at the weighbridge than at a roadside inspection.
Before towing
If you are towing for the first time with a loaded vehicle, weigh the vehicle before hitching up. Then hitch the trailer and weigh again. The difference tells you your actual towball download. If the total exceeds GVM, you have a problem to solve before you drive.
If you are considering a GVM upgrade
Get a weighbridge reading of your actual loaded vehicle before buying a GVM upgrade. You may find you are well within 3,500 kg and do not need the upgrade at all. Or you may confirm you are regularly at 3,450 kg and the upgrade is clearly justified.
Buying guide: how to choose the right payload path
Stay stock and manage weight carefully if:
- Your canopy build and daily load sit comfortably under 500 kg total (including driver)
- You do not tow regularly or only tow light trailers
- You travel with one or two occupants, not four or five
- You are willing to weigh the vehicle and manage your load actively
Simplify your build if:
- You are close to the limit and do not want to spend $4,190 on a GVM upgrade
- You can swap a heavy canopy for a lighter one (aluminium instead of fibreglass or steel saves 20–50 kg)
- You can remove accessories you rarely use (rooftop tent you used once, heavy steel bull bar on a ute that never goes off road)
- You can shift from a double drawer system to a single drawer and save 15–25 kg
Consider a GVM upgrade if:
- Your real world loaded weight (weighed, not guessed) consistently sits above 700 kg of payload used
- You tow regularly with a loaded vehicle and the maths are consistently tight
- You are building a full touring setup with canopy, fridge, battery, water and rooftop tent
- You are a tradie carrying heavy tools plus picking up passengers and towing daily
- You want genuine legal headroom instead of constantly calculating margins
What we recommend at Oz Canopies & 4×4: Start with the maths. Weigh the vehicle if you can. Talk to us about your build plan and we will run the payload numbers with you before you commit to a canopy, drawers or accessories. If the numbers say you need a GVM upgrade, we will point you in the right direction. If they say you do not, we will save you $4,190. Call 02 9627 8666 or text 0440 130 098.
FAQs
What is the BYD Shark 6 payload?
What is the BYD Shark 6 GVM?
What is the Shark 6 kerb weight?
Does towball weight count as payload?
Can a canopy setup push the Shark 6 over payload?
Does the Shark 6 have a GVM upgrade available?
What does the Ironman Shark 6 GVM upgrade increase it to?
Does a GVM upgrade also increase towing?
Is VSB 14 the same as state approval rules?
Do I need a GVM upgrade for a touring build?
Your next step: do the maths, then decide
Here is the fastest way to know where you stand:
- Fill in the payload worksheet above with your actual setup (or planned setup). Be honest about weights.
- If remaining payload is over 200 kg: You are in a comfortable zone on stock GVM. Manage weight sensibly and you are fine.
- If remaining payload is 50–200 kg: You are in the caution zone. Weight discipline matters on every trip. Consider whether simplifying the build or upgrading GVM makes more sense for your use case.
- If remaining payload is under 50 kg or negative: You are at or over GVM. Either lighten the build significantly or get a GVM upgrade.
Need help running the numbers on your build? Drop into the Oz Canopies & 4×4 showroom at 20 Walker St, South Windsor, call 02 9627 8666 or text 0440 130 098. We will work through your payload budget with you before you commit to a canopy, drawers or any accessory package.
Browse our full range of BYD Shark 6 accessories online.