How to Choose and Mount a Rooftop Tent on a BYD Shark 6

Setting up a rooftop tent on a Shark 6 involves more than checking whether the tent physically fits on the…

By Chris 18 min read Published Last updated:

How to Choose and Mount a Rooftop Tent on a BYD Shark 6
Table of contents

Setting up a rooftop tent on a Shark 6 involves more than checking whether the tent physically fits on the roof. The owner needs to account for the weight of the tent itself, the crossbars or platform underneath it, mounting brackets and hardware, any awning or recovery gear attached to the same rack and the difference between dynamic load (driving) and static load (parked with people sleeping inside).

The Shark 6’s cab roof has a dynamic load allowance of approximately 75 kg. That number includes everything on the roof, not just the tent. Once you subtract the rack, brackets and hardware, the leftover capacity for the tent itself is often tighter than people expect.

This guide compares three mounting paths (cab roof, canopy roof and tub rack), walks through the weight calculations, covers real tent weights from current Australian market products and explains how to choose and mount an RTT safely.

Quick answer: where should you mount an RTT on a Shark 6?

Cab roof

Best for a genuinely lightweight tent on lightweight crossbars. Keeps the tub and canopy clear. Mostly suited to sealed road or moderate touring use.

The main limitation is that the tent, rack, brackets and all attached accessories must fit within the cab roof’s 75 kg dynamic allowance. Many midweight and heavy tents exceed this before the rack is even added.

Canopy roof

Best for touring builds where the owner already has a structural aluminium canopy. Easier integration with awnings and solar. A wider range of tent weights becomes realistic because quality aluminium canopies are often rated to 150 to 250 kg dynamic on their own roof.

The main limitation is that the canopy must be explicitly rated for RTT use and the entire load path (tent, rack, canopy roof, canopy frame, canopy mounts, tub) must support the load.

Tub rack

Best for keeping the tent lower, retaining open tub space underneath and avoiding the cab roof weight ceiling entirely. Tub racks like the HSP Load Rack JNR are rated to 150 kg dynamic, giving serious headroom for most tents.

The main limitation is that the tub rack, its feet and the tub attachment points all need to handle dynamic and off road loads.

Short recommendation

For most Shark 6 owners, the best path is:

  • Cab mounting only for a genuinely light tent and a lightweight crossbar setup
  • Canopy mounting for a full touring build where the canopy is already part of the plan
  • Tub rack when keeping the tent low and the tub flexible matters most

Understand the Shark 6 roof load limits before choosing a tent

This is the most important section in the article. Get these numbers wrong and the rest of the build is compromised.

What 75 kg dynamic means

Dynamic load is the weight the cab roof can carry while the vehicle is moving. The calculation includes everything attached to the roof:

Total dynamic load = tent weight + rack or platform weight + mounting hardware + attached accessories (awning, solar, recovery tracks)

The result must not exceed the lowest applicable dynamic rating in the system.

For the Shark 6 cab roof using factory raised rails with aftermarket crossbars or a platform, that limit sits at approximately 75 kg. For a detailed breakdown of how this number works across cab, canopy and tub rack setups, including the “lowest number wins” rule, see the BYD Shark 6 roof racks and platforms guide.

What 300 kg static means

Static load applies when the vehicle is parked. The general industry rule of thumb puts the Shark 6 cab roof static rating at roughly 225 to 300 kg. This is the number that matters when two adults climb into the tent at camp.

Static load must accommodate the tent, rack, hardware, occupants, bedding and anything stored inside the tent. It does not allow the vehicle to drive with 300 kg on the roof. Static is parked only.

The lowest rated component rule

The final real world limit is determined by the weakest link in the chain:

  • Vehicle roof structure
  • Factory rails or mounting points
  • Rack feet or legs
  • Crossbars or platform
  • RTT mounting brackets
  • Canopy or tub rack (if mounting there)
  • Off road rating (if driving on unsealed roads)

A rack rated for 100 kg does not increase a vehicle roof rated to 75 kg. A canopy rated to 200 kg does not override a tub mounting system rated to 150 kg. The lowest number always wins.

Why cab mounting is difficult but not impossible

The 75 kg budget disappears quickly

Here is a worked example using realistic component weights:

Component Weight (kg)
Lightweight hardshell RTT (e.g. Alu Cab LT 50 with mattress) ~51
Crossbars and feet (pair) ~10
Mounting brackets and hardware ~3
Total travelling load ~64 kg
Remaining before 75 kg limit ~11 kg

That 11 kg margin is workable on sealed roads. But add a small awning bracket (2 kg) and a set of recovery track mounts (3 kg) and you are at 69 kg with only 6 kg to spare. Add bedding stored inside the tent during travel and you can exceed the limit without realising it.

Full platforms make the maths harder

A roof platform (17 to 25 kg with legs) provides better accessory mounting, but it eats significantly more of the available weight budget than a pair of crossbars (5 to 10 kg). On the Shark 6 cab roof, lightweight crossbars almost always make more sense than a heavy platform under an RTT.

Do not add accessories without recalculating

A cab mounted tent may technically fit within the limit until the owner adds an awning, shovel mounts, traction boards, a solar panel or bedding carried inside the tent during travel. Every gram counts. Recalculate after every addition.

Common mistake: Buying a tent that weighs 55 kg, assuming “that’s under 75 kg, so it fits.” It does not. The 75 kg includes the tent, the rack, the brackets and every accessory attached to the same system. The tent weight is the starting point, not the answer.

When cab mounting makes sense

Recommend cab mounting only where:

  • The complete fitted system (tent + rack + hardware + accessories) stays under 75 kg dynamic
  • The rack manufacturer expressly approves RTT use
  • Minimum crossbar spacing is met per the tent manufacturer’s instructions
  • The vehicle will not carry substantial additional roof gear on the same system
  • Off road derating has been checked if the owner drives on unsealed roads

Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney if you want help running the numbers for a specific tent and rack combination.

Canopy mounted rooftop tents

Why canopy mounting is often the better touring option

A properly rated aluminium canopy opens up the RTT conversation significantly. Instead of squeezing everything into 75 kg on the cab roof, a canopy with a 150 to 250 kg dynamic roof rating gives you room for a heavier tent, an awning, solar panels and recovery gear, all on one platform.

Other advantages:

  • The cab roof stays unloaded (better aerodynamics, less noise)
  • Gear can be organised as one integrated touring system
  • The tent sits over the tub, keeping the cab profile clean
  • Wider tent choice because weight is less constrained

The canopy must be structurally rated

Not every canopy can carry an RTT. Before committing, check:

  • Dynamic roof rating (published by the canopy manufacturer)
  • Static roof rating
  • Whether RTT use is expressly permitted in the product documentation
  • Required number and spacing of crossbars or load points
  • Internal canopy bracing and frame construction
  • How the canopy mounts to the tub (clamp on, bolt on or rail system). Mounting method affects the entire load path and the BYD Shark 6 clamp on vs bolt on canopy mounting guide explains the trade offs.
  • Whether off road use reduces the published rating

Canopy roof rating is not the only number

The complete load path for a canopy mounted RTT runs:

RTT → bars or platform → canopy roof → canopy frame → canopy mounts → tub

A strong canopy roof rating is meaningless if the canopy to tub mounting is weak. The entire chain must support the load.

Aluminium vs fibreglass canopy for RTT use

Structural aluminium canopies are the most common choice for RTT builds because they offer high roof load ratings (often 150 to 250 kg dynamic) combined with integrated mounting channels and lower weight. Some fibreglass canopies can carry lighter RTTs, but only where the manufacturer provides an appropriate rating and mounting system. Material alone does not determine suitability. The aluminium vs fibreglass canopy comparison for BYD Shark 6 covers the structural and weight differences in detail.

Tub rack mounted rooftop tents

Why a tub rack can be a strong option

A standalone tub rack bypasses the cab roof entirely. Benefits include:

  • The tent sits lower than a cab roof or tall canopy installation, reducing the centre of gravity and wind exposure
  • The open tub can be preserved underneath (depending on rack height)
  • Tub racks can be removed or reconfigured more easily than a permanent canopy
  • Load ratings of 150 kg dynamic are common (e.g. HSP Load Rack JNR), giving genuine headroom for most tents

Low, mid height and cab height racks

  • Low rack: Keeps the RTT below or close to the cab roofline. Best for aerodynamics and overall vehicle height. Limited tub clearance underneath.
  • Mid height rack: Balances tub access and overall height. Enough clearance for gear underneath, but the RTT sits higher.
  • Cab height rack: Provides more tub clearance and can align accessories across the vehicle, but places the RTT at the highest point.

Check compatibility with other tub accessories

Tub racks may conflict with roller shutters, hard lids, factory sports bars, tonneau covers or powered cover mechanisms. If you are also considering a hard lid or roller shutter instead of a Shark 6 canopy, plan the complete tub system before buying any single component.

Rooftop tent weight comparison

All weights below are from current manufacturer specifications. Verify before purchase, as models and specifications change.

Lightweight RTTs (realistic for cab roof mounting)

Brand / Model Type Weight Sleeps Cab roof viable?
Alu Cab LT 50 (with mattress) Hardshell ~51 kg 2 Yes (with light crossbars)
Darche Intrepidor 2 Soft shell ~51 kg 2 Yes (with light crossbars)
Yakima SkyRise HD Medium Soft shell ~52 kg 2 to 3 Yes (with light crossbars)

These are the most realistic starting point for a Shark 6 cab mounted setup. With a 10 to 14 kg crossbar and bracket system, total dynamic load sits at roughly 64 to 67 kg, leaving a small margin under 75 kg.

Midweight RTTs (canopy or tub rack recommended)

Brand / Model Type Weight Sleeps Cab roof viable?
Bush Company LX27 Hardshell clamshell ~73 kg 2 No (exceeds 75 kg with rack)
Bush Company AX27 Hardshell clamshell ~99 kg 2 No

A tent in this weight range consumes or exceeds the cab roof dynamic allowance before rack weight is included. Canopy or tub rack mounting is the practical path.

Heavy expedition RTTs (canopy or tub rack only)

Brand / Model Type Weight Sleeps Cab roof viable?
Bush Company TX27 Hardshell ~123 kg 2 No

These are canopy, tub rack or trailer oriented choices only. The complete mounting structure must be engineered and rated for the load.

Soft shell vs hardshell RTT for the Shark 6

Soft shell advantages

  • Often lighter than hardshell equivalents
  • Usually lower purchase price
  • Larger sleeping footprint for the packed size
  • Better chance of fitting within a tight cab roof budget

Soft shell disadvantages

  • Longer setup and pack down time
  • Greater wind noise or drag depending on design and travel cover
  • More fabric maintenance
  • Less protection when packed

Hardshell advantages

  • Quicker setup (many open in under 60 seconds)
  • Lower profile options available
  • Better weather protection when packed
  • Integrated rails and accessory mounting on some models (e.g. Alu Cab LT 50 carries 30 kg on its roof)

Hardshell disadvantages

  • Many models are too heavy for the Shark 6 cab roof
  • Higher purchase price
  • More strain on canopy or rack systems
  • Owners may be tempted to load additional accessories on the shell

Do not assume all soft shell tents are light or all hardshell tents are heavy. Compare actual product weights, not categories.

Off road derating and corrugation loads

Why off road ratings may be lower

Corrugations, ruts and sudden body movement apply greater forces than smooth sealed road travel. The repeated jolting multiplies the stress on every mounting point, bracket and fastener.

Manufacturers may publish a separate off road rating, apply a reduction factor or require additional crossbars for off road use. Do not invent a universal percentage. Instead, obtain the off road rating for your specific rack system, canopy, tub rack and RTT mounting kit.

Recheck after rough travel

After any serious dirt road trip, check:

  • Bracket torque on all mounting points
  • Rack rails and mounting feet for movement or fretting
  • Canopy or tub rack mounts for looseness
  • Seal and gasket condition at mounting interfaces
  • The tent itself for any damage or shifted components

Make this a habit before every major trip. The NTC Load Restraint Guide for Light Vehicles provides the baseline principles for securing cargo and equipment and those same principles apply to a rooftop tent and everything attached to it.

How to calculate your complete RTT setup weight

Use this worksheet before buying anything.

Step 1: Record the tent’s travelling weight. Confirm whether the published weight includes the mattress, ladder, mounting rails, travel cover and internal bedding. If it excludes the mattress or ladder, add them.

Step 2: Add the supporting system. Crossbars, rack feet, platform, mounting rails, brackets and fasteners.

Step 3: Add permanent accessories. Awning and brackets, solar panel, recovery tracks and mounts, tent roof rails, lights and any bedding or gear carried inside the tent during travel.

Step 4: Compare against every rating. Check the dynamic rating (vehicle or mounting structure), static rating, off road rating, rack rating and tent mounting system rating. The lowest number applies.

Step 5: Keep a sensible margin. Do not build to the exact published ceiling, especially for regular corrugated road use. A 5 to 10 kg buffer is good practice.

Common mistake: Weighing the tent, seeing 51 kg and declaring “plenty of room under 75 kg.” The tent is one component. The crossbars, feet, brackets, awning and anything else on the same rack all count. Add up every gram.

Mounting the rooftop tent: planning level steps

This is a planning guide, not a replacement for manufacturer installation instructions.

Step 1: Confirm all ratings and compatibility. Total weight, bar spacing, mounting hardware, opening direction, ladder clearance and tailgate or canopy door clearance.

Step 2: Position the bars or platform. Ensure bars are square, parallel and spaced per the tent manufacturer’s instructions. Torque feet or rail mounts to specification.

Step 3: Lift the tent safely. Use enough helpers or a workshop hoist. Avoid dragging the tent across the rack. Protect vehicle paint and canopy surfaces.

Step 4: Fit approved mounting hardware. Use supplied or manufacturer approved brackets, correct channel nuts, locking nuts where specified and corrosion resistant hardware.

Step 5: Check clearances. Rear hatch or canopy doors, ladder deployment, awning clearance, roof antenna, brake light visibility, tailgate opening, solar panels and any other roof accessories.

Step 6: Torque and document. Record torque settings, installation date, component part numbers and recheck interval.

Step 7: Short test drive and inspection. Low speed noise check, braking and cornering check, fastener inspection, movement check and a second torque check after the initial drive.

Payload, centre of gravity and driving behaviour

The RTT and its supporting system count toward the Shark 6’s overall vehicle payload. The BYD Shark 6 payload and GVM guide explains how the 790 kg payload budget works and where every kilogram goes.

An RTT must be considered alongside passengers, canopy, drawers, fridge, battery, water, tools, towball download and touring gear. On the Shark 6, a 70 kg RTT plus 20 kg rack system is 90 kg, which is roughly 11% of the entire payload budget consumed by the tent alone.

A heavy tent mounted high also affects body roll, braking distance, crosswind sensitivity, fuel and energy consumption, off road stability and clearance under trees and in car parks. Mount as low as practical and remove the tent when it is not needed.

Best Shark 6 RTT setup by owner type

Lightweight weekender

  • Tent: approximately 46 to 55 kg (Alu Cab LT 50, Darche Intrepidor or similar)
  • Mounting: lightweight crossbars on the cab roof
  • Accessories: no permanent awning or heavy cab roof accessories
  • Total system: under 70 kg dynamic
  • Best for: sealed road weekend trips, occasional bush camps

Touring canopy build

  • Tent: 50 to 80 kg (broader range available due to higher canopy roof rating)
  • Mounting: crossbars or platform on a structurally rated aluminium canopy
  • Accessories: awning, solar panel and recovery gear planned as one system
  • Best for: regular touring, extended dirt road travel, integrated camping setups

Browse the BYD Shark 6 canopy range to compare canopies with published roof load ratings suitable for RTT use.

Open tub camping build

  • Tent: 50 to 100 kg
  • Mounting: low or mid height tub rack (e.g. HSP Load Rack JNR at 150 kg dynamic)
  • Accessories: tent positioned close to the cab line, tub retained for bikes, boxes or gear
  • Best for: owners who want the tent without a canopy, mixed use between camping and tub utility

Heavy expedition tent

  • Tent: 100+ kg (Bush Company AX27, TX27 or similar)
  • Mounting: heavy duty canopy or engineered tub rack with published dynamic and off road ratings
  • Professional installation recommended
  • Payload and axle load review essential (consider the Ironman GVM upgrade to 3,850 kg if the total build is heavy)
  • Best for: extended remote touring, serious overlanding

What we recommend at Oz Canopies & 4×4: For most Shark 6 owners, the sweet spot is a lightweight hardshell tent on a canopy or tub rack. This avoids the 75 kg cab roof bottleneck, gives room for an awning and solar and keeps the build within a sensible payload budget. Come talk to us about matching a tent to your canopy and rack setup.

Common mistakes to avoid

  • Comparing only tent weight and forgetting the rack, brackets and hardware
  • Treating the 300 kg static figure as a driving limit (it is parked only)
  • Assuming a 75 kg rated rack increases the vehicle’s cab roof rating (lowest number wins)
  • Adding an awning after the weight calculation is done without recalculating
  • Buying a heavy hardshell tent before choosing its mounting location
  • Assuming every canopy can carry an RTT (check the published roof rating)
  • Ignoring off road derating for unsealed road travel
  • Carrying bedding, pillows and accessories inside the tent during travel without counting their weight
  • Using incorrect crossbar spacing (check the tent manufacturer’s minimum and maximum requirements)
  • Failing to re torque mounting hardware after the first trip and after corrugated roads
  • Overlooking total vehicle payload (the tent, rack and everything else on the ute counts toward the 790 kg limit)
  • Mounting the tent so canopy doors or the tailgate cannot open properly

Rooftop tent buying checklist for Shark 6 owners

  • < > Published tent weight confirmed (check what is included and excluded)
  • < > Mattress and ladder weight confirmed separately if excluded
  • < > Mounting hardware weight added
  • < > Rack or platform weight added
  • < > Dynamic rating checked for mounting location (cab, canopy or tub rack)
  • < > Static rating checked
  • < > Off road rating checked (if driving on unsealed roads)
  • < > Mounting location chosen (cab, canopy or tub rack)
  • < > Minimum crossbar spacing confirmed per tent manufacturer instructions
  • < > Opening direction checked (does it clear the cab, canopy or other accessories?)
  • < > Ladder length checked for vehicle and mounting height
  • < > Canopy door and tailgate clearance confirmed
  • < > Awning and solar panel weight included in the total
  • < > Total vehicle payload recalculated with the RTT system included
  • < > Installer requirements confirmed
  • < > Torque and recheck schedule documented

FAQs

Can you fit a rooftop tent to a BYD Shark 6?

Yes. The Shark 6 can carry an RTT on the cab roof (if the total system stays under 75 kg dynamic), on a canopy roof (if the canopy is rated for it) or on a tub rack (rated to 150 kg+ dynamic on many models). The mounting location determines which tents are practical.

What is the Shark 6 cab roof load limit?

Approximately 75 kg dynamic (while driving) using the factory raised rails with aftermarket crossbars or a platform. Static (while parked) is roughly 225 to 300 kg. The 75 kg includes the rack, brackets, tent and all attached accessories.

Does the 75 kg limit include the roof rack?

Yes. The 75 kg dynamic limit covers everything on the cab roof: crossbars or platform, legs, mounting hardware, tent, awning brackets and any other accessories. The leftover after subtracting the rack system is what is available for the tent.

Is a canopy better than the cab roof for a rooftop tent?

For most builds, yes. A structurally rated aluminium canopy with 150 to 250 kg dynamic roof capacity gives far more headroom for heavier tents, awnings and accessories. Cab mounting only suits genuinely lightweight setups.

Can a fibreglass canopy support an RTT?

Only if the manufacturer provides a specific roof load rating that covers RTT use. Some fibreglass canopies can carry lighter tents, but the structural design, internal bracing and published rating must confirm suitability. Aluminium canopies are more commonly used for RTT builds due to higher roof load ratings.

Does an awning count toward the dynamic roof load?

Yes. An awning, its brackets and any other accessories attached to the same rack or canopy roof all count toward the dynamic load total. A 2 m awning typically adds 15 to 25 kg packed.

Do people sleeping in the tent count toward the static load?

Yes. Occupants, bedding, pillows and anything inside the tent count toward the static load while parked. The static rating (225 to 300 kg for the cab roof, higher for most canopies and tub racks) must cover the tent, rack, people and contents.

How often should RTT mounts be checked?

After the first 100 km, before and after every trip on unsealed roads and at least every 3 to 6 months during regular use. Corrugations and rough roads loosen fasteners faster than most people expect.

Your next step: choose the mounting location first

The fastest way to narrow down your Shark 6 RTT setup:

  1. Is the complete tent and rack system under 75 kg? If no, the cab roof is out. Use a canopy or tub rack.
  2. Will you also mount an awning, solar panel or extra gear on the same system? If yes, a canopy or tub rack gives you more room.
  3. Do you want to keep the tub open underneath? A tub rack retains tub utility.
  4. Are you building a full touring canopy rig? The canopy roof is the most integrated mounting path.

Choose the mounting location first. Calculate the complete system weight second. Only then choose the tent.

For the full picture of how an RTT fits into a complete Shark 6 canopy build, including payload maths, electrics, storage layouts and mounting options, the BYD Shark 6 canopy and tub setup guide ties everything together.

Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney to talk through your RTT options.