Towbar installation

A towbar is a metal device that attaches to the rear of a vehicle that is used to tow trailers,…

By Chris 10 min read Published Last updated:

LDV Towbars
Table of contents

A towbar is a metal device that attaches to the rear of a vehicle that is used to tow trailers, caravans, or other vehicles. The installation process of a towbar varies based on the make and model of the vehicle you have and the type of vehicle (car, ute, SUV or truck etc.) you have.

Towbar installation process is:

  1. Make sure the towbar kit you have is for your vehicle
  2. Prepare the vehicle by removing the rear bumper if applicable
  3. Locate the towbar mounting points
  4. Attach the towbar to the vehicle
  5. Install the trailer / towbar wiring harness
  6. Refit the rear bumper and panels
  7. Do final checks to make sure all the wiring is working and all bolts are tight

A step by step guide for towbar installation is as follows:

Make sure the towbar kit you have is for your vehicle

Towbars are all designed to be model specific, with bolt holes drilled in them to match the holes in your vehicle’s chassis to make installation of the towbar possible and safe. All ADR (Australian design rules) approved towbars must come with a pair of towbar labels which contain information about the make and model the towbar is intended to be fit on and the maximum towing capacity etc. which provides an easy way to check and see if you have the correct towbar for your vehicle. The towbar may also come with an installation manual that you should read thoroughly.

Another thing to be mindful of is making sure that you have the correct wiring harness for your vehicle. Direct fit (Plug and Play) harnesses are model specific and are easier to fit, but are typically more expensive. Universal style harnesses require splicing into the vehicle’s tail light cluster to fit, so some knowledge about using an electrical test light (or at least having a wiring diagram handy) and solder will be required, but are generally cheaper.

Prepare the vehicle

Park the vehicle on a flat surface with its parking brake engaged.

If the vehicle is a car or SUV, remove the rear bumper of the vehicle to get access to the towbar mounting points on the chassis. If the vehicle is a ute the chassis mounting points may be immediately accessible.

If removing a rear bumper, be cautious and proceed slowly. Modern bumpers can have many screws and plastic clips holding them in place and you want to avoid breaking any of them.

Locate the towbar mounting points

Using the towbar as a guide, locate the mounting holes on the vehicle’s chassis / frame that correspond with the holes that are on either end of your towbar. These are the holes that are going to be used to affix your towbar to your vehicle.

Attach the towbar to the vehicle

  1. Position the towbar over the mounting holes on the vehicle, aligning the holes on either end of the towbar with the holes on the vehicle’s frame / chassis.
  2. Use the provided bolts, washers and nuts to secure the towbar. Hand-tighten the bolts at first to ensure proper alignment and avoid cross threading.
  3. If the towbar requires drilling, use the towbar to mark the spots carefully. Drill a pilot hole before using a larger drill bit to expand the hole. Make sure to paint over any holes drilled into your vehicle to prevent rust forming.
  4. Then use the provided nuts and bolts to continue securing the towbar.
  5. Torque all bolts to the manufacturer’s specifications using a torque wrench.

Install the trailer / towbar wiring harness

If using a direct fit harness:

  1. Locate the plug on the vehicle which the harness plugs into. This is usually located in the boot area for cars and SUV’s, or along the frame for Utes. The instruction manual on the harness will help you locate this plug.
  2. Some direct fit harnesses still require you to attach them to some kind of constant 12v power source e.g the vehicle’s battery or a power socket. Refer to the harnesses instructions to determine if this is the case.
  3. If a 7 pin plug is not already attached the trailer end of the harness, wire that up using the following diagram:

If you’re using a hard wire / universal wiring harness:

  1. If you have a wiring diagram that corresponds to the specific make and model, connect the wiring harness to the vehicle’s wires as per the diagram. This is done by stripping the wires and soldering them on. Once all the wires are soldered make sure to wrap any open electrical connections with electrical tape to prevent any short circuits. It is advisable to disconnect the negative terminal of the vehicle’s battery while doing this as well to once again minimise the risk of short circuits.
  2. If you don’t have a wiring diagram for the vehicle, you will need to use an automotive test light to identify which wires in the vehicles taillight cluster correspond with the indicators, brake light, parkers etc. Once these are all identified, you can begin soldering the wiring harness to the vehicle.
  3. Some universal wiring harnesses require you to attach them to some kind of constant 12v power source e.g the vehicle’s battery or a power socket. Refer to the harnesses instructions to determine if this is the case.
  4. If a 7 pin plug is not already attached the trailer end of the harness, wire that up using the following diagram:
    • Pin 1 – Left Indicator – Yellow
    • Pin 2 – AUX / Reverse – Black (typically not found on most wiring harnesses)
    • Pin 3 – Earth – White
    • Pin 4 – Right Indicator – Green
    • Pin 5 – Electric Brakes – Blue
    • Pin 6 – Stop Brakes – Red
    • Pin 7 – Tail lights / Parkers – Brown

Whether you use a direct fit or universal wiring harness, the next step is to test the wiring harness using a trailer or circuit tester to make sure all the lights are functioning correctly.

Refit the rear bumper and panels

  1. If the rear bumper was removed, refit it by reversing the steps you made to remove it.
  2. You will find for most cars and SUVs, the bumper will not fit directly back onto the vehicle because it fouls with the towbar’s hitch receiver. To re-fit the bumper in this case, it will need to be cut to allow space for the hitch receiver. This is done by holding up the bumper as close to its original position as possible and marking out where the hitch receiver bumps into it. Once these markings are made, it is time to start cutting into the bumper with a multi tool. It is best practice to cut less depth in the bumper than you need at first, mocking it up with the receiver again to make new markings and making further cuts as needed to get the cleanest fit and finish.
  3. Make sure that the trailer wiring harness is routed correctly to allow you to mount the 7 pin plug to either the bumper or towbar once finished for easy access.

Final checks

  1. Double check all the bolts to make sure that they are tight.
  2. Make sure the 7 pin plug is mounted securely, then test the wiring again to make sure it is behaving as expected.
  3. Double check that the tail lights and rear bumper of the vehicle have been re-fitted correctly.

How to choose the right towbar

Besides making sure the towbar you choose suits your vehicle, there are a whole heap of towbar manufacturers and suppliers in Australia to consider before making your purchase. Here are a few great reasons to purchase your new towbar from Oz Canopies & 4×4:

  1. Lifetime warranty – All the towbars we supply come with a lifetime warranty*
  2. The best prices – We sell so many towbars that we can push our suppliers to give us the best prices, savings that we transfer straight to you. We pride ourselves in making sure you get the best price in town.
  3. All Aussie team – Our Sydney based team have been around towbars for over a decade, so we know what we’re talking about.
  4. In house expert fitment – We don’t only supply towbars, our expert Sydney based mechanical shop can fit your towbar and wiring harness for a small fee, giving you peace of mind that your towbar kit has been fitted correctly.

Want to find out more or book your car or ute in to get a towbar fitted? Give us a call on 02 9627 8666 or contact us here!

How to choose the correct person to install your towbar

A towbar is a safety critical item, so it’s very important to choose the right person to fit your towbar kit to your car or ute. There are horror stories out there of people who didn’t get their towbar fitted correctly and have run into mechanical or electrical trouble or even complete towbar failure. Here are few reasons why you should get your towbar fitted at Oz Canopies & 4×4:

  1. One stop shop: Buy your towbar, the towbar wiring kit and have it all fitted in the one convenient Sydney location. Save yourself time and money.
  2. Experts in towbar fitting: We’ve been fitting towbars for over a decade, and have hands-on experience with basically every vehicle that can tow. That’s how we can make sure your towbar is fitted right, the first time.
  3. The best prices: We push our suppliers to give us the best prices that we transfer directly to our customers, so you get the best price on a brand new towbar fitted to your car or ute.
  4. 700+ 5 Star Google Reviews: Don’t take our word for it, just have a quick look at our google reviews to see just how much our customers love us.

Can I install a towbar by myself?

We get this question fairly often, and the answer is: it depends. A towbar kit can be considered a moderately difficult item to install on a car or ute, and the difficulty of the installation process depends on the vehicle you’re considering putting a towbar on. For example, utes are easier to fit towbars to because a rear bumper doesn’t need to be removed before fitting a towbar.

However, at Oz Canopies & 4×4, we’ve made it as easy as possible for you to give a shot at fitting your own towbar kit, by putting together fitting videos for some of our most popular models. We’re also always available to give you expert advice about fitment over the phone.

So if you want to have a crack at fitting your towbar kit yourself, or you live a little bit too far away to have us fit a towbar kit for you, Oz Canopies & 4×4 is the best place to supply you the right towbar kit at the right price.

How much does it cost to install a towbar?

The cost to install a towbar ranges between $200 – $500. The cost will depend on the make and model of your vehicle. Fitting towbars on utes is typically easier & cheaper because there are not many body panels to remove, whereas European built cars and SUVs attract a higher fitting cost because it takes more time to remove panels to get access to towbar mounting points and their wiring systems are more complex.

Still got some questions?

Our all Aussie team is ready to chat right away on 02 9627 8666, or if you prefer to leave us a message you can text us on 0440 130 098 or on our contact page here!

We’re experts in the trade and are always happy to give you the right advice in picking the right towbar kit for your car or ute!

*Lifetime warranty is conditional on the towbar being used exclusively for towing purposes, fitted correctly and is not transferable.