GWM Cannon Canopy Setup Guide: How to Choose the Right Canopy Without Blowing Your Payload or Your Budget
The GWM Cannon is one of the sharpest value propositions in the Australian ute market. With a 4×4 dual cab…
Table of contents
The GWM Cannon is one of the sharpest value propositions in the Australian ute market. With a 4×4 dual cab starting from around $34,000 MLRP and a seven year warranty across the range, tradies, tourers and weekend warriors are buying them fast.
But here is what happens next.
You buy the Cannon because the price is right. Then you start shopping for a canopy, drawers, a roof rack, a fridge, maybe an awning or rooftop tent. Before you know it, you have spent $8,000 to $15,000 on accessories and you still have not checked whether your ute can legally carry all of it.
That is the real tension with the Cannon. The purchase price is low, but the setup decisions that follow are anything but simple. The Cannon’s dual cab payload typically sits around 995 kg. On the XSR it drops to around 875 kg. Add a canopy, a roof platform, drawers, a fridge, water, recovery gear, passengers and towball weight and you can chew through that payload frighteningly fast.
This guide covers fitment, use case, weight, roof loads, towing, pricing and setup recipes so you can choose the right canopy the first time. Whether you are running a Cannon as a work ute, a touring rig, a tow vehicle or a bit of everything, the information here is practical and specific to the Cannon. No fluff, no filler, just advice from a team that fits canopies to utes every week.
Quick answer: what is the best canopy for a GWM Cannon?
It depends on how you use the ute.
Work use: A heavy duty aluminium tub or tray canopy with side access, shelving and central locking. Steel is an option for maximum toughness, but the weight penalty hits Cannon payload hard.
Touring use: An aluminium tub canopy with a drawer system, fridge slide, dual battery and modest roof load. Keep the roof setup light. The Cannon is not a LandCruiser, so every kilogram on the roof matters more than you think.
Mixed or weekend use: A fibreglass or lightweight aluminium tub canopy with central locking and a basic interior light. Lower cost, cleaner look, minimal weight impact.
Towing use: Go as light as possible on the canopy. Towball download weight counts against payload, so a heavy canopy plus heavy trailer setup can push you over GVM before you have loaded anything else.
The golden rule: Do the payload maths before you commit to any canopy purchase. Not after.
Which GWM Cannon does this guide apply to?
The Cannon range has grown and changed names over the past few years, so it is worth being clear about what we are talking about.
Current Cannon range at a glance
The table below covers the current Cannon lineup. Specifications are based on manufacturer data current at the time of writing. Pricing reflects MLRP (manufacturer list retail price) excluding on road costs and may change without notice. Check with your dealer for current driveaway pricing.
| Variant | Engine | Tow (braked) | GVM | Approx. Payload | MLRP from |
|---|---|---|---|---|---|
| Premium SC CC 4×2 | 2.0L diesel, 8sp auto | 3,200 kg | 3,050 kg | ~1,150 kg | $33,990 |
| Premium DC 4×4 | 2.0L diesel, 8sp auto | 3,200 kg | 3,135 kg | ~995 kg | $37,990 |
| Lux DC 4×4 | 2.4L diesel, 9sp auto | 3,500 kg | 3,225 kg | ~995 kg | $40,490 |
| Lux DC CC 4×4 | 2.4L diesel, 9sp auto | 3,500 kg | 3,225 kg | ~995 kg | $42,490 |
| Ultra DC 4×4 | 2.4L diesel, 9sp auto | 3,500 kg | 3,225 kg | ~995 kg | $44,490 |
| Vanta DC 4×4 | 2.4L diesel, 9sp auto | 3,500 kg | 3,225 kg | ~995 kg | $46,490 |
| XSR DC 4×4 | 2.4L diesel, 9sp auto | 3,500 kg | 3,205 kg | ~875 kg | $49,490 |
All Cannon variants use 4×4 drivetrains except the Premium SC CC (4×2). Lux and above run the newer 2.4 litre turbo diesel producing 135 kW and 480 Nm. Premium models retain the proven 2.0 litre with 120 kW and 400 Nm. All variants except the XSR hold a five star ANCAP safety rating (awarded 2021). The entire range carries a seven year, unlimited kilometre warranty.
The key number for canopy planning is the payload column. Most dual cab tub Cannons give you around 995 kg. The XSR drops to approximately 875 kg due to its heavier off road equipment (snorkel, bash plates, front diff lock, heavier all terrain tyres). The Premium Single Cab Chassis stands out with approximately 1,150 kg payload because of its lighter kerb weight and the fact that the standard aluminium tray is included in the kerb figure.
Dual cab tub vs cab chassis: why this changes your whole canopy decision
This is a fork in the road moment that many Cannon buyers do not think about early enough.
If you have a dual cab tub (Premium DC, Lux, Ultra, Vanta, XSR), you are choosing between tub mounted canopies, hard lids or roller shutters. The canopy sits on or clamps to the existing tub walls. This is the simpler and cheaper path for most owners and it is where the majority of Cannon canopy buyers end up.
If you have a cab chassis (Premium SC CC or Lux DC CC), you need a tray first, then a canopy on top. This is a completely different setup conversation with different weight implications, different costs and different fitment requirements. The tray choice shapes everything that goes on top, from canopy style to shelving layout to roof load capacity. For a deeper look at that decision, read Tray vs Tub: What is Best for Your Ute?.
Common mistake: Buying a cab chassis Cannon with a plan for a simple tub canopy. It does not work that way. You need a tray first and the tray choice shapes everything on top.
Key dimensions that affect fitment
| Measurement | Dual Cab Tub | Notes |
|---|---|---|
| Tub length | ~1,520 mm | Internal usable length |
| Tub width | ~1,520 mm | Wall to wall |
| Width between wheel arches | ~1,140 mm | Too narrow for standard AU pallet (1,165 mm) |
| Tub depth | ~540 mm | |
| Wheelbase | 3,230 mm | Affects weight distribution behind axle |
| Overall length (range) | 5,331 to 5,703 mm | Varies by variant and body style |
| Overall height (range) | 1,884 to 1,997 mm | Before canopy or roof rack is added |
| Ground clearance | 212 to 232 mm | Canopy overhang affects departure angle |
These numbers matter for canopy planning. Canopy overhang beyond the tub can affect rear departure angle and tail light visibility. Tub width determines internal drawer and shelving layouts. Height matters if you are adding a roof platform, rooftop tent or ladder racks, as you may end up too tall for covered car parks or low clearance worksites. The wheelbase influences weight distribution when you stack heavy gear behind the rear axle.
Do not confuse GWM Cannon with Cannon Alpha
The Cannon Alpha is a different vehicle. The Alpha range currently includes three drivetrain options: a 2.4 litre turbo diesel (shared with the standard Cannon), a full hybrid (HEV) using a 2.0 litre turbo petrol with an electric motor producing a combined 255 kW and 648 Nm and a plug in hybrid (PHEV) producing a combined 300 kW and 750 Nm.
The Alpha uses coil springs at the rear instead of leaf springs, has a different tub design and carries significantly more kerb weight. The HEV weighs approximately 2,575 kg with around 735 kg payload. The PHEV weighs approximately 2,810 kg, leaving only about 685 kg of payload. These are dramatically different numbers from the standard Cannon and they change every part of the canopy and accessory calculation.
Canopy fitment, weight planning and setup advice for the Alpha differ enough to deserve separate coverage. The principles in this article about payload budgets, towing maths and material choices still apply, but the specific numbers will not match an Alpha rig.
Start with the job your Cannon actually needs to do
Before you look at a single canopy brochure, answer one question: what does this ute actually need to do most of the time? Your answer determines the canopy type, material, access style, roof setup and accessory list. Get this wrong and you will either overspend, overweight or end up ripping it all out within a year.
Work ute
A Cannon set up for trade work needs to carry tools, parts, materials and sometimes ladders. It needs to be secure enough to leave on a job site overnight without losing your angle grinder. It needs to handle daily abuse, dust, rain and the occasional bump from a forklift.
Priorities for a work canopy are side access (gullwing or lift up windows for grabbing gear without climbing into the tub), central locking that integrates with the ute remote, internal shelving or racking and a roof system rated for ladder carrying. LED interior lighting is not optional. You will be reaching into the back of the canopy at 5:30 am in winter and you need to see what you are grabbing.
For a heavy duty work setup, a tray canopy usually makes more sense than a tub canopy. Trays give you more mounting options, more floor space and better modularity for shelving and tool compartments. If you want to know more about the security angle, What Are The Benefits Of A Lockable Ute Canopy? covers the essentials.
Touring and camping rig
A Cannon set up for touring needs to carry a fridge, a drawer system, a dual battery, water, an awning, recovery gear and potentially a rooftop tent. The priorities here are weather sealing (you do not want dust or water getting into your food and sleeping gear), good ventilation, easy rear access for the drawer system and enough roof capacity for your platform or tent without blowing the weight budget.
Aluminium canopies dominate the touring space because they offer the best strength to weight ratio. You need every kilogram you can save on the canopy itself, because the gear going inside it adds up fast. A 995 kg payload sounds generous until you start adding drawers, a fridge, a battery, water and two passengers.
Mixed use family and weekend setup
This is the most common Cannon buyer profile. You drive the ute to work during the week, maybe carry some gear in the back and then load it up for camping, fishing or sports on the weekend.
Priorities here are daily drivability (not too tall for the shopping centre car park), secure storage (you do not want your tools or sports gear visible through the rear window), lower weight (because you are not building a full touring rig), easier access and a clean appearance that does not look like a tradie ute at the school drop off.
A tub mounted fibreglass or lightweight aluminium canopy with central locking and a rear window is usually the simplest path for this use case.
Towing focused setup
If you tow a caravan, boat, box trailer or horse float regularly, your canopy decision is all about weight control.
Towball download weight (the downward force the trailer puts on the towball) counts as payload. Maximum downball weight is 320 kg on the Premium Single Cab Chassis and Premium Dual Cab, and 350 kg on the Lux, Lux Dual Cab Chassis, Ultra, Vanta and XSR. If your caravan has a 300 kg ball weight, that is 300 kg gone from your payload before you have put a single thing in the tub. Add a tub canopy at 65 to 85 kg and your remaining payload for passengers, gear and fuel is getting thin quickly.
Towing focused Cannon owners should go as light as possible on the canopy, avoid heavy roof setups and plan their accessory list with a calculator in hand. We work through the maths in detail further down this article.
GWM Cannon canopy types explained
For a broader look at what is available across all utes, The Different Types of Ute Canopies is a good starting point.
Tub canopy
A tub canopy mounts onto the existing tub walls of your Cannon. It is the most common type for dual cab tub buyers because it is the simplest install, the widest range of options and usually the lowest cost.
Who it suits: Weekend users, mixed use owners, light tourers, daily drivers who want secure covered storage.
Pros: Easier to install (no drill clamp systems often available), lower cost than tray conversions, wide range of materials and styles, easier to remove if you sell the ute or change direction.
Limitations: Limited to the tub dimensions (that 1,520 mm length is not massive), no under tray storage, less modular than tray setups and the tub walls are the structural limit for roof loads.
Typical weight: 60 to 85 kg for an aluminium tub canopy. 70 to 85 kg for fibreglass. This is the canopy shell only, not including drawers, racks or other accessories fitted inside or on top.
For most Cannon owners who want a canopy for everyday use, a tub canopy is the easiest path forward.
Tray canopy
A tray canopy sits on an aftermarket tray, which replaces the factory tub entirely (on a cab chassis) or is mounted after tub removal (less common on dual cabs but it happens).
Who it suits: Tradies who need maximum internal space, serious tourers who want a purpose built storage system and cab chassis buyers who need a complete rear solution.
A tray canopy gives you more floor area, better mounting options for shelving and drawers and the ability to build a fully modular storage system. Many heavy duty service canopies use this format because it allows side opening tool compartments, full depth shelving and custom racking.
Key weight distinction: A tray canopy system includes the tray itself plus the canopy on top. The combined weight of an aluminium tray (100 to 180 kg) plus a canopy (60 to 100 kg) typically runs 180 to 280 kg total. A steel tray alone can weigh 200 to 300 kg before the canopy goes on. Do not confuse tub canopy weights (60 to 85 kg for the canopy shell) with full tray plus canopy system weights (180 to 350 kg depending on material). They are fundamentally different setups with fundamentally different payload impacts.
Lift up windows vs sliding windows vs gullwing access
Lift up windows are hinged at the top and prop open with gas struts. They offer wide access, decent weather sealing when closed and they double as a rain shelter when open. Most touring and mixed use canopies run this style.
Sliding windows sit in a track and slide open horizontally. They are cheaper, allow ventilation while driving (important for dogs or airflow) and do not stick out when open. The downside is narrower access and weaker sealing compared to lift up styles.
Gullwing doors are full side opening panels, hinged at the top, that open upward like wings. These give the widest possible access and are brilliant for tradies who need to grab tools from the side without walking around to the back. They are more expensive and heavier than standard windows, but the convenience on a work ute is hard to beat.
Common mistake: Choosing windows purely on looks. Think about how you will actually access the canopy day to day. If you are constantly reaching in from the side on a work site, gullwing or lift up windows will save you time and frustration compared to a rear access only setup.
Full height canopy vs low profile canopy vs lid or roller
Full height canopy is the right call when you need maximum internal volume, the ability to mount roof accessories (racks, platforms, tents) or when you are building a touring or work setup with drawers and shelving. This is what most people picture when they think “canopy”.
Low profile canopy sits lower than cab height, usually just above the tub walls. These look sleek, add less wind drag and less weight and still give you lockable covered storage. The trade off is reduced internal height, which limits drawer depth and rules out taller items like eskies or large toolboxes.
Hard lid is a flat, lockable cover that sits flush with the tub walls. Minimal weight, clean look, easy access via a flip up or tri fold design. Some hard lid systems support light roof bars or crossbars, while others offer no roof capacity at all. Always check the specific product rating before assuming you can mount anything on top. For a comparison between these approaches, check out Hard Lid vs Canopy vs Roller Shutter.
Roller shutter is a retractable cover that rolls toward the cab when opened. Sharp look, minimal weight, good tub access. Most roller shutters offer limited or no weather sealed enclosed space, limited side access and reduced roof load options, though some newer systems include integrated crossbars for light loads. The specifics vary by product, so check the individual rating rather than assuming all rollers are the same.
Aluminium vs steel vs fibreglass for a GWM Cannon
Material choice is one of the most important decisions in the canopy process and it is where a lot of Cannon owners get it wrong by choosing on price alone.
| Factor | Aluminium | Steel | Fibreglass |
|---|---|---|---|
| Tub canopy weight (typical) | 60 to 85 kg | 100 to 150 kg | 70 to 85 kg |
| Rust resistance | Excellent (no rust) | Requires coating maintenance | Excellent (no rust) |
| Dent resistance | Moderate | High | Low (can crack) |
| Roof load suitability | Good to high | High | Low to moderate |
| OEM appearance | Moderate | Low (industrial look) | Excellent (colour matched) |
| Modularity | High | High | Low |
| Relative cost | Mid to high | Mid | Low to mid |
| Best for | Touring, mixed, towing | Heavy commercial | Daily driver, weekender |
Aluminium canopies
Aluminium is the most popular canopy material in Australia for good reason. It is lighter than steel (a typical aluminium tub canopy weighs 60 to 85 kg), it does not rust, it is strong enough for moderate to high roof loads and it takes well to powder coating.
For a Cannon with 995 kg of payload, aluminium saves 40 to 65 kg compared to an equivalent steel canopy. That is meaningful weight you can redirect toward gear, passengers or towball load. Aluminium canopies suit touring builds, mixed use setups, towing focused builds and any owner who needs to watch their payload closely.
The downside is that aluminium canopies are generally more expensive than fibreglass and they can dent under heavy impact. But for most Cannon owners, the weight saving justifies the premium.
Steel canopies
Steel canopies are built like tanks. They resist dents better than aluminium and suit owners who put their ute through genuinely heavy commercial abuse: mining, construction, rural work where the canopy is going to cop hits from branches, gear and loading equipment.
The penalty is weight. A steel tub canopy for a Cannon can weigh 100 to 150 kg, which is 40 to 65 kg heavier than an equivalent aluminium canopy. On a ute with 995 kg of payload, that is a meaningful difference that ripples through every other accessory and loading decision. Steel also requires coating maintenance to prevent rust if the finish gets damaged. For a detailed comparison, Steel vs Aluminium Ute Canopy lays it out clearly.
Fibreglass canopies
Fibreglass canopies are the closest thing to an OEM factory look. They are smooth, colour matched and they blend with the cab profile in a way that makes the ute look like it came off the lot that way.
Fibreglass suits everyday owners who want a clean appearance, basic secure storage and a canopy that does not look like a work rig. The weight is moderate, typically 70 to 85 kg for a tub canopy with windows.
The limitations show up when you start loading the roof. Fibreglass canopies generally carry lower roof load ratings than aluminium, which means they are less suitable for rooftop tents, heavy platforms or serious rack systems. They can also crack under heavy impact or flex on rough corrugated roads.
Which material suits which Cannon owner?
Tradie: Aluminium if you want the best balance of strength and weight. Steel only if you genuinely need maximum dent resistance and accept the payload cost.
Camper or tourer: Aluminium, almost always. You need the weight saving for all the gear going inside the canopy and on the roof.
Weekender or daily driver: Fibreglass if appearance matters most. Aluminium if you want more flexibility down the track.
Budget buyer: Fibreglass tub canopies are often the cheapest entry point. But a cheap heavy canopy that eats your payload budget is a false economy.
Towing heavy buyer: Choose aluminium and keep the canopy setup as light as practical. Every kilogram added to the canopy reduces the vehicle’s remaining payload and may also reduce trailer headroom once GCM becomes the limiting factor.
Payload, towing and GVM maths every GWM Cannon owner should understand
This is the section most canopy buyers skip. Do not be one of them.
The GWM Cannon is a capable ute, but its payload is not unlimited. If you add a canopy, accessories and gear without doing the maths, you can end up overweight, outside compliance and exposed on insurance. And you might not even know it until you hit a weighbridge or have an incident.
What your payload has to cover
Payload is not just the stuff in the tub. It is everything you add to the vehicle above its factory kerb weight, up to the GVM limit. That includes the canopy itself, roof racks or platform, drawers, fridge, battery system, water tank, recovery gear, toolboxes, every passenger in the vehicle, fuel above the amount included in the kerb weight figure, aftermarket bull bar (if heavier than factory), aftermarket wheels and tyres, towbar and towball download weight when towing.
The following table shows typical weight ranges for common canopy accessories. Actual weights vary by brand and specification.
| Item | Typical Weight | Notes |
|---|---|---|
| Aluminium tub canopy | 60 to 85 kg | Canopy shell only |
| Fibreglass tub canopy | 70 to 85 kg | Canopy shell only |
| Steel tub canopy | 100 to 150 kg | Canopy shell only |
| Aluminium tray (alone) | 100 to 180 kg | Before canopy is fitted on top |
| Steel tray (alone) | 200 to 300 kg | Before canopy is fitted on top |
| Roof platform (aluminium) | 20 to 35 kg | |
| Drawer system (single or dual) | 40 to 70 kg | Includes slides |
| Compressor fridge (40 to 60L) | 18 to 25 kg | Empty weight |
| Dual battery system | 25 to 35 kg | Battery, DC DC charger, wiring |
| Water (40 litres + tank/pump) | 45 to 50 kg | Full weight including water |
| Rooftop tent | 50 to 70 kg | Folded, without bedding |
| Awning (standard side) | 12 to 18 kg | |
| 270 degree awning | 22 to 30 kg | Significantly heavier than standard |
| Recovery gear (basic kit) | 15 to 25 kg | Strap, shackles, shovel, boards |
| Steel bull bar (over factory) | 40 to 60 kg | Weight added above factory bumper |
| Rock sliders (pair) | 30 to 50 kg | |
| Each additional passenger | ~85 kg | Standard compliance figure |
Why towing changes everything
Towing is where Cannon payload budgets get really tight. The Cannon Lux, Lux Cab Chassis, Ultra, Vanta and XSR are rated to tow up to 3,500 kg braked, while the Premium variants are rated to 3,200 kg. Maximum downball weight is 350 kg on the 2.4-litre variants and 320 kg on the Premium variants. The actual towball load forms part of the coupled vehicle’s mass and consumes payload.
You also need to consider GCM, or Gross Combined Mass. When the trailer is coupled, calculate the actual combined mass by adding the Cannon’s coupled vehicle mass, including the towball load, to the mass carried by the trailer’s axles. Do not add the trailer’s complete aggregate mass to an already-coupled vehicle mass because that counts the towball load twice.
For example, the Cannon Ultra has a 6,200 kg GCM. If a fully loaded trailer weighs 3,500 kg and places 350 kg on the towball, the trailer’s axles carry the remaining 3,150 kg. If the coupled Cannon is at its 3,225 kg GVM, the actual combination weighs 6,375 kg, which is 175 kg over the 6,200 kg GCM. To remain within the 6,200 kg GCM in this example, the coupled Cannon could weigh no more than 3,050 kg. Before the 350 kg towball load is transferred onto the vehicle, that means a maximum loaded vehicle mass of 2,700 kg, leaving approximately 470 kg above the Ultra’s published 2,230 kg kerb weight for the canopy, towbar, occupants, accessories and vehicle cargo. This is why maximum trailer weight and full vehicle payload cannot normally be used together.
| Item | Weight |
|---|---|
| Actual loaded trailer mass | 3,500 kg |
| Towball mass | 350 kg |
| Mass remaining on trailer axles | 3,150 kg |
| Cannon at GVM, including ball mass | 3,225 kg |
| Actual coupled combination | 6,375 kg |
| GCM | 6,200 kg |
| Actual exceedance | 175 kg |
Example payload budgets
These are rough guides based on a Cannon with 995 kg payload (Lux/Ultra/Vanta). Weights are approximate and vary by product.
| Setup | Canopy/Tray | Accessories | Total Added | Remaining Payload |
|---|---|---|---|---|
| Light daily driver | Alum. tub canopy: 70 kg | Roof bars 15 kg, LED 2 kg, lock 2 kg | ~89 kg | ~906 kg |
| Tradie (tub based) | Alum. tub canopy: 80 kg | Gullwing, racks 20 kg, shelving 30 kg, LED 3 kg | ~135 kg | ~860 kg |
| Tradie (tray based) | Alum. tray + canopy: 220 kg | Racks 20 kg, shelving 30 kg, LED 3 kg | ~275 kg | ~720 kg |
| Weekend camping | Alum. tub canopy: 75 kg | Platform 25 kg, drawers 50 kg, fridge 22 kg, battery 30 kg, awning 15 kg | ~217 kg | ~778 kg |
| Full touring | Alum. tub canopy: 80 kg | Platform 30 kg, RTT 55 kg, drawers 60 kg, fridge 22 kg, battery 35 kg, water 45 kg, recovery 20 kg | ~347 kg | ~648 kg |
| Towing + canopy | Alum. tub canopy: 70 kg | Roof bars 15 kg, drawers 50 kg, towball load 250 kg | ~385 kg | ~610 kg |
On the XSR (approximately 875 kg payload), subtract a further 120 kg from each “remaining payload” figure. The full touring setup would leave roughly 528 kg, which gets tight with two passengers and a week of gear.
GVM, GCM and axle loads in plain English
GVM (Gross Vehicle Mass) is the maximum your Cannon can legally weigh when fully loaded, including the vehicle itself, all accessories, all passengers, all cargo and fuel. On the Cannon Ultra, that is 3,225 kg.
GCM (Gross Combined Mass) is the maximum permitted actual mass of the coupled vehicle-and-trailer combination. When coupled, calculate it by adding the loaded Cannon’s mass, including the imposed towball load, to the mass carried by the trailer’s axles. Do not add the complete trailer ATM to the coupled vehicle mass because the towball component would be counted twice. On the Cannon Ultra, the GCM is 6,200 kg. With a trailer actually weighing 3,500 kg and placing 350 kg on the towball, the trailer axles carry 3,150 kg, leaving a maximum of 3,050 kg for the coupled Cannon before reaching GCM.
Axle loads are the maximum weight each axle can carry. These are separate from GVM and can be the limiting factor even when you are under GVM. Overloading the rear axle (which is where all the tub weight sits) is one of the most common problems with canopy equipped utes. This is especially relevant when the Cannon leaf spring rear end is loaded up with a heavy canopy, drawers and gear.
The Department of Infrastructure and Transport publishes Vehicle Standards Bulletin 14 (VSB 14), the national code of practice covering light vehicle modifications in Australia. It is the baseline framework for understanding how modifications, including canopy fitting, interact with vehicle compliance.
Why this is not just about legality
An overloaded Cannon has longer braking distances. The rear suspension compresses further, lifting the front end and reducing steering grip. Tyres run hotter and wear unevenly. Off road, the risk of bottoming out and damaging suspension components increases significantly.
From an insurance perspective, exceeding GVM or GCM may give your insurer grounds to reduce or deny a claim. This is not a guaranteed outcome in every situation, but it is a well documented risk that is worth discussing with your insurer before you finalise a heavy build. Check your policy wording around vehicle modifications and load compliance.
The National Transport Commission’s Load Restraint Guide for Light Vehicles is a useful resource here. It frames load restraint around staying secure under braking (forward force at 80% of load weight), sideways forces at 50%, rearward at 50% and upward at 20% if the load is not fully contained. These performance standards apply to canopy setups, not just truck loads.
Roof load limits, racks and rooftop tent planning
The roof is prime real estate on any canopy equipped ute. But it is also where some of the most expensive mistakes happen.
Cab roof vs canopy roof vs platform system
These are three different things with three different load ratings and confusing them is a recipe for problems.
The cab roof has its own load rating set by the vehicle manufacturer. Aftermarket roof racks or bars that mount to the cab rails are rated by the rack manufacturer, but they cannot exceed what the cab roof itself can handle.
The canopy roof has a separate rating set by the canopy manufacturer. This is the number that matters when you are loading the canopy and it varies widely depending on canopy material, construction and how the load is distributed.
A roof platform distributes load across a wider area of the canopy roof. It adds weight itself (20 to 35 kg typically) but allows you to spread a load more evenly and mount accessories like awnings, recovery boards and solar panels in organised positions.
Dynamic vs static roof load
This catches a lot of people out, especially rooftop tent buyers.
Dynamic load is the rated weight the roof can carry while the vehicle is moving. This is the smaller number, accounting for forces from braking, cornering and rough roads. For many canopies, dynamic load is in the range of 70 to 100 kg.
Static load is the rated weight when parked and stationary. This matters for rooftop tents, because the tent is only occupied when parked. Static ratings are usually two to three times higher than dynamic.
Common mistake: Adding a rooftop tent (55 kg), a platform (30 kg), an awning (15 kg) and recovery boards (10 kg) and assuming the canopy handles 110 kg dynamic while driving. Most canopy roofs cannot. You need to check the dynamic rating for the total weight on the roof while moving, not just the static rating that applies when camped.
Common roof load mistakes on GWM Cannon setups
Overloading the roof with RTT plus awning plus platform plus recovery boards plus jerry cans is the number one mistake we see. The combined weight of all those items can easily hit 100 to 130 kg, which exceeds many canopy dynamic ratings.
Another common error is assuming that because the canopy is strong enough to hold the weight, everything else is fine. The weight on the canopy roof transfers down through the canopy walls to the tub or tray, then to the suspension and axles. You need to account for roof load weight in your total payload calculation and your rear axle loading.
Rough road use amplifies everything. A 100 kg roof load on a smooth highway behaves very differently to a 100 kg roof load on a corrugated outback track. The dynamic forces multiply, which is why dynamic load ratings exist.
Best roof setup by use case
Tradie ladder carrying: A pair of heavy duty roof bars or a low profile ladder rack. Keep it simple, keep it rated for the load and make sure the bars are spaced to support the full length of your longest ladder.
Light touring: A roof platform with awning brackets and tie down points. No need for a heavy steel platform. Aluminium options are lighter and adequate for moderate loads.
Rooftop tent build: A rated platform on a canopy rated for both static and dynamic loads appropriate to your tent weight. Check both the canopy rating and the platform rating. The weakest link in the chain is what matters.
Kayak, surfboards, bikes: Dedicated carriers on roof bars or platform crossbars. Lightweight, low profile and properly secured for highway speeds.
Best GWM Cannon canopy setups by owner type
This is where theory becomes practical. Here are five setup recipes based on how real Cannon owners use their rigs.
Setup 1: Budget daily driver with secure storage
This is the simplest and lightest canopy setup. You want lockable covered storage for tools, shopping, sports gear or the dog, without adding significant weight or complexity.
Go with a fibreglass or lightweight aluminium tub canopy. Add central locking that integrates with the ute key fob. Install one or two LED strip lights inside so you can see what you are grabbing. Add a rubber or carpet mat to the tub floor for protection. Skip the heavy drawer system, skip the roof platform, skip the dual battery. You do not need them for this use case.
Approximate weight added: 65 to 85 kg (canopy plus basic accessories). Budget range: $2,000 to $4,500 installed.
Setup 2: Tradie workhorse
Tradies need a canopy that works as hard as they do. Security, access and organisation are the priorities.
Start with an aluminium tub canopy with gullwing side access or an aluminium tray canopy if you are on a cab chassis. Add internal shelving or racking sized to your trade (electricians, plumbers and builders all need different internal layouts). Install central locking. Add LED lighting, both internal strips and a work light for the rear.
If you carry ladders, add a rated roof rack system. Consider skipping drawers if you work off the tailgate a lot. A flat tub floor with a storage system you can pull toward you is often more practical for site work than a fixed drawer unit.
Tub based approximate weight: 120 to 160 kg. Tray based approximate weight: 250 to 310 kg (tray plus canopy plus shelving). Budget range: $5,000 to $10,000 (tub) or $10,000 to $18,000 (full tray conversion).
Setup 3: Weekend touring Cannon
This is the setup for the owner who camps a few times a month and wants a capable but not over the top rig.
An aluminium tub canopy with lift up rear window and at least one lift up side window. Add a drawer system with a fridge slide. Fit a compressor fridge (40 to 60 litres). Install a dual battery system with a DC DC charger. Mount an awning to the canopy or a light roof platform.
Keep the roof load modest. An awning and maybe a set of recovery boards is enough. If you want a rooftop tent, check the canopy roof rating carefully before committing.
Approximate weight added: 220 to 280 kg. Budget range: $7,000 to $12,000 installed.
Setup 4: Serious touring and off grid build
This is the full build. You are going remote, you are going for extended trips and you need self sufficiency.
Start with an aluminium tub canopy (or tray canopy on a cab chassis). Fit a full drawer and storage system. Install a fridge and fridge slide. Add a lithium or dual battery system with a DC DC charger and possibly solar panels. Fit a water tank with a pump (40 to 60 litres minimum). Install a UHF radio and phone antenna for remote communication. Add recovery gear: rated recovery points, a snatch strap, shackles and a shovel.
Weight is the critical factor here. A full touring build can easily weigh 340 to 420 kg before passengers and personal gear. On a Cannon with 995 kg of payload, that leaves 575 to 655 kg. Two passengers at 85 kg each, food for a week, clothing and camp cooking gear will use 300 to 400 kg. You are running close to the limit, so every item needs to earn its place.
Budget range: $12,000 to $20,000 plus.
Setup 5: Towing and family touring
This setup prioritises keeping weight down so you have payload headroom for towball download and the family.
Choose the lightest canopy you can find. A slim aluminium tub canopy or even a hard lid might be enough if you do not need full enclosed storage on every trip. Avoid heavy roof setups. If you need drawers, choose a lighter single drawer unit with a fridge slide instead of a full dual drawer system.
Common mistake: Building a full touring rig with RTT, heavy drawers and a 100 kg canopy, then also towing 3,000 kg on weekends. The maths does not work. Choose one focus or build a setup that is deliberately light enough to flex between both.
Approximate weight added: 80 to 150 kg (canopy and minimal accessories). Budget range: $2,500 to $6,000.
Security, dust sealing, weather sealing and daily usability
What actually matters in day to day ownership
Locking points and central locking are non negotiable. At minimum, you want a rear door lock that cannot be easily forced and ideally a central locking system that ties into the factory remote. If you are storing valuable tools or electronics, Which Type Of Locks Are Most Secure For Ute Canopies? covers the lock options in more detail.
Compression seals around all doors and windows keep water and dust out. Cheap canopies with basic rubber strips will leak eventually, especially on corrugated roads where the canopy flexes. Look for proper compression seals that create a positive seal when closed.
Drainage around the base of the canopy is often overlooked. Water that runs down the outside needs somewhere to go. If it pools around the seal line, it will eventually find a way inside.
Worksite vs touring practicality
On a work site, you want fast side access, open floor space (more useful than drawers for throwing bags and boxes in and out) and shelving that stops things sliding. For touring, rear access is king for drawers and the fridge, weather sealing matters more because you are sleeping next to the canopy and side windows need to open for ventilation without giving full gullwing access.
Interior lighting, ventilation and convenience
LED lighting inside the canopy should be bright enough to find what you need at night and positioned to avoid shadows. A single strip light along the roof centreline is the minimum. Side lights or under shelf lights are even better for work setups.
Ventilation matters more than most people realise. A sealed canopy in Australian summer heat becomes an oven. If you are carrying a fridge, poor airflow makes the fridge work harder and drain more power. Sliding windows, pop out vents or small louvres in the rear door keep air moving. GWM’s own accessory catalogue includes a 12V tub smart socket, which simplifies wiring accessories directly into the tub.
Canopy accessories worth adding from day one vs later
Add from day one
Central locking is best fitted during canopy installation because it involves wiring into the vehicle locking system. Retrofitting later means pulling trim panels and running cables that should have gone in during the initial install.
LED lighting is cheap and easy to add during install. Having the wiring done while the canopy is being fitted saves time and money later.
Roof rails or a platform backbone should go on at install if you know you will use the roof. Adding a platform later can mean removing and remounting the canopy in some cases.
Tie down points and basic organisation (cargo barriers, cargo nets, a tub mat) are cheap, lightweight and immediately useful.
Add later
Drawer systems are a significant investment. Unless you know exactly what layout you need, live with the canopy for a few weeks first and figure out how you actually use the space.
Fridge slides and fridges can wait until you have a camping trip planned. Easy to install later.
Awnings mount to the canopy side or roof rails. Straightforward to add at any time.
Power systems (dual battery, DC DC charger, solar) are best done when you have a clear picture of your electrical needs.
Accessories that look cool but add weight fast
A steel roof platform (30 to 45 kg), a rooftop tent (50 to 70 kg), a 270 degree awning (22 to 30 kg), a steel bull bar (40 to 60 kg over factory), rock sliders (30 to 50 kg per pair). Stack them all up and you can use 500 to 600 kg of payload before a single passenger gets in. On a 995 kg payload ute, that is the kind of arithmetic that leads to compliance problems.
Installation, fitment and legal considerations
Tub mounted vs tray mounted fitment
Tub mounted canopies clamp or bolt to the tub walls. The installation is usually simpler, faster and cheaper. Tray mounted canopies bolt to the tray, which is itself bolted to the chassis. This is a more structural installation and usually needs professional fitting.
No drill vs drill dependent installs
Some canopy brands offer no drill clamp systems for tub mounted canopies. These clamp to the inner tub walls without permanent modification, which is great if you plan to remove the canopy later or want to preserve resale value. Drill dependent installs use bolts through the tub walls or rail, giving a more rigid mount but creating permanent holes that need sealing.
Wiring, brake lights, central locking and accessory integration
Any canopy that covers the factory tail lights needs its own brake lights and indicators. This is a legal requirement under the Australian Design Rules (ADRs). Reputable canopy suppliers include these and wire them during installation. Additional accessory wiring should be done neatly and safely, with cables protected from metal edges and water exposure.
Weight distribution and axle loading
Everything in the canopy sits behind or over the rear axle. This shifts weight rearward, which can lighten the front axle, reduce steering response and affect braking balance. Mount heavy items (drawers, fridge, water) as far forward in the tub as possible, close to the axle line.
If a canopy setup significantly changes weight distribution or pushes beyond factory GVM, a GVM upgrade through the Vehicle Assessment Signatory Scheme (VASS) in Victoria or equivalent state based engineering certification, may be needed to maintain compliance.
Why load restraint still matters after the canopy is fitted
Fitting a canopy does not automatically restrain everything inside it. Loose items will still fly forward under hard braking. The NTC’s Load Restraint Guide specifies that loads must be restrained to handle 80% of load weight forward, 50% sideways and rearward and 20% upward if not fully enclosed. A cargo barrier behind the cab, straps and properly fitted drawers all contribute to meeting these requirements.
Common mistake: Assuming a closed canopy equals a restrained load. A 20 kg toolbox loose on the tub floor will fly forward under hard braking, canopy or not. For more on keeping your setup safe, Aluminium Ute Tray Canopy Safety: What You Need to Know is a useful read.
What does a GWM Cannon canopy setup cost?
These are ballpark budget ranges to help you plan, not firm quotes. Prices vary by brand, features and installation complexity.
| Setup Level | What It Includes | Budget Range (installed) |
|---|---|---|
| Budget tub canopy | Fibreglass or entry level aluminium tub canopy, rear window, central locking, LED light | $2,000 to $4,500 |
| Mid range aluminium | Aluminium tub canopy, lift up side windows, central locking, LED lighting, roof bars | $4,500 to $7,500 |
| Heavy duty work (tub) | HD aluminium tub canopy, gullwing access, shelving, roof rack, LED work lights | $7,000 to $12,000 |
| Touring with electrical | Aluminium canopy, drawers, fridge slide, dual battery, DC DC, awning, roof platform | $10,000 to $18,000 |
| Tray + canopy conversion | Aluminium tray, canopy, electrical, shelving or drawers, lighting, roof setup | $12,000 to $25,000+ |
A note on value: The Cannon’s low purchase price means many buyers have more room in their overall vehicle budget for accessories. A $40,000 Cannon with $15,000 of well chosen canopy and accessories can be a better equipped rig than a $60,000 competitor with $5,000 of cheap add ons. The key is spending that money wisely, on the right setup, at the right weight.
How to choose the right GWM Cannon canopy in 5 steps
If the detail above feels like a lot, here is the streamlined decision process.
Step 1: Confirm whether you have a tub or a cab chassis. Tub buyers choose from tub canopies, lids or rollers. Cab chassis buyers need a tray plus canopy system. This single fact narrows your options by half.
Step 2: Define the job. Work? Touring? Mixed use? Towing? Each use case has different priorities for access style, weight, features and roof load. Be honest about what you will actually use the ute for 80% of the time, not the one annual trip to Cape York.
Step 3: Choose your material. Aluminium for the best weight to strength ratio. Steel for maximum durability in heavy commercial use. Fibreglass for the cleanest OEM look at the lowest cost. Match the material to the job from step 2.
Step 4: Do the payload maths. Add up the canopy weight, every accessory, your typical passenger load and towball weight if towing. Compare the total to your Cannon payload rating (995 kg for most dual cabs, 875 kg for XSR). If you are over, something has to change before you buy.
Step 5: Choose your access and roof system. Lift up, sliding, gullwing or rear only access based on daily use. Roof bars, platform or nothing based on what you need to carry and what the canopy can support.
What we recommend at Oz Canopies & 4×4
We have fitted canopies to dozens of GWM Cannons and the pattern is clear. Most Cannon buyers are value focused. They bought the ute because the price to spec ratio is outstanding and they want the same kind of value from their canopy setup.
For the majority of Cannon owners, a well built aluminium tub canopy is the right starting point. It keeps weight down, it is strong enough for moderate roof loads, it does not rust and it leaves you payload headroom for the accessories you will add over time.
If you are a tradie running a cab chassis Cannon, a properly designed aluminium tray and canopy system gives you the modularity and access you need without the weight penalty of steel.
And if you are purely after secure covered storage with a clean look, a fibreglass canopy at the right price is still a solid choice for a daily driver.
Whatever direction you go, we always start the conversation with the same question: what do you need this ute to do? Start there and the right canopy choice usually becomes obvious. Oz Canopies & 4×4 has been fitting setups to match owner needs since 1998, backed by 700+ five star Google reviews.
Frequently asked questions
What canopy fits a GWM Cannon?
Is the GWM Cannon good for a touring canopy setup?
Can you put a rooftop tent on a GWM Cannon canopy?
Is aluminium or steel better for a GWM Cannon canopy?
How much payload does a GWM Cannon have after fitting a canopy?
Can you tow 3.5 tonnes with a canopy fitted?
Is a tray canopy better than a tub canopy for the GWM Cannon?
Does the GWM Cannon Alpha use the same canopy as the standard Cannon?
What is the best GWM Cannon canopy for tradies?
What is the best GWM Cannon canopy for camping?
Want us to sanity check your build list?
Choosing a canopy for a GWM Cannon comes down to three things: knowing what the ute needs to do, choosing the right material and setup for that job and making sure the total weight stacks up before you commit.
If you are still not sure whether you need a tub canopy, a tray canopy or a lid, send us your Cannon model and variant along with a quick note about how you use the ute. We will put together a recommendation that suits your job, your weight budget and your accessory plans. No pushy sales pitch. Just practical advice from a team that does this every day. Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor, Sydney. We are open six days a week and happy to walk you through the options in person.