BT-50 Rooftop Tent Setup: Weight, Roof Ratings & Mounting Guide
A rooftop tent is one of the most popular upgrades for a touring BT-50. Fast to set up, off the…
Table of contents
A rooftop tent is one of the most popular upgrades for a touring BT-50. Fast to set up, off the ground, comfortable to sleep in and it turns the ute into a genuine mobile camp in under two minutes. It’s easy to see why they’re everywhere.
But rooftop tents are also one of the most commonly miscalculated accessories on a BT-50 canopy build. The tent might weigh 60kg folded. The rack adds another 20kg. An awning adds 18kg. A solar panel adds 12kg. Mounting hardware adds 5kg. That’s 115kg sitting on the canopy roof before you even open the tent. And when you open it and two adults climb in, the static load can exceed 250kg.
Not every BT-50 canopy can handle that. Some canopy roof systems are rated at 75 to 100kg dynamic. That’s barely enough for the folded tent and rack while driving and well short of safety on corrugated roads where forces multiply.
The question isn’t “can you put a rooftop tent on a BT-50?” The answer to that is yes, you can. The real question is: “Can your specific canopy, rack and mounting system safely support a rooftop tent while driving, while parked and on the roads you actually use?”
This guide walks through everything you need to check before buying an RTT for your BT-50: dynamic load, static load, off road load, canopy ratings, rack ratings, weight stacking, mounting considerations and the payload impact on the vehicle.
For the detailed roof load theory, the BT-50 roof load limits guide explains dynamic, static and off road ratings in full. For the complete build picture, the Mazda BT-50 canopy setup guide covers every part of a BT-50 canopy build.
Quick answer: can you put a rooftop tent on a BT-50 canopy?
Yes, but only if the entire system is rated for it. That means:
- The canopy roof is rated for the dynamic load (tent + rack + accessories while driving)
- The rack or platform is rated for the load
- The static rating covers the tent plus occupants while parked
- The off road rating suits your intended use on unsealed roads
- The total roof setup doesn’t overload the BT-50’s payload
Mazda’s own BT-50 accessory ratings illustrate why this matters. The genuine roof platform is rated at 70kg on road and 47kg off road. The canopy roof rail kit is rated at 75kg, rising to 150kg with an optional reinforcement kit. A folded rooftop tent plus rack typically weighs 70 to 100kg. On the standard 75kg canopy rails, that’s already over the limit. On the reinforced 150kg rails, it fits comfortably. Same vehicle, very different outcome depending on the system.
Before you buy an RTT, check these:
- Rooftop tent weight (folded, including mattress and mounting rails)
- Rack or platform weight
- Awning weight (if fitted)
- Solar panel weight (if fitted)
- Canopy dynamic roof load rating
- Canopy static roof load rating
- Off road roof load rating (or estimate at 50 to 60% of dynamic)
- Total vehicle payload remaining
If any single component in the chain is under rated, the setup isn’t suitable. The lowest rated part wins.
Rooftop tent weight: what actually counts?
When people talk about RTT weight, they usually quote the manufacturer’s tent weight. But the tent is only one part of the total roof load.
What counts toward roof load when driving (dynamic):
| Component | Typical Weight |
| Rooftop tent (folded, with mattress) | 50 to 80kg |
| Roof rack or crossbars | 8 to 25kg |
| Mounting rails/brackets | 3 to 8kg |
| Awning | 10 to 20kg |
| Solar panel (fixed) | 8 to 15kg |
| Recovery boards (pair) | 6 to 10kg |
| Shovel/axe bracket | 2 to 4kg |
| Bedding left inside tent | 3 to 8kg |
| Typical total (RTT + rack + awning) | 85 to 140kg |
That 85 to 140kg is the dynamic load your canopy roof must support while driving. If your canopy is rated at 100kg dynamic, a setup at the heavier end of that range is over the limit before you account for off road force multiplication.
What counts when parked (static):
Everything above, plus the weight of anyone sleeping in the tent. Two adults at 75kg each adds 150kg. A tent with 80kg of hardware and two adults creates a static load of around 230kg. Your canopy needs a static rating that covers this comfortably.
Common mistake: Only checking the tent’s advertised weight and assuming that’s the number to compare against the canopy rating. The actual roof load is the combined system weight: tent + rack + awning + solar + hardware + bedding. Always add everything up.
Dynamic vs static roof load: why RTT setups need both numbers
Dynamic load: when the BT-50 is moving
Dynamic roof load is the maximum weight the canopy roof can handle while the vehicle is driving. This is the rating that matters every time you drive with the RTT on the roof.
When the vehicle brakes, accelerates, corners and hits bumps, the forces on the roof multiply well beyond the static weight. A 70kg folded tent on the roof doesn’t exert just 70kg of force when you hit a pothole at 80km/h. The peak dynamic forces can be two to three times the static weight for brief moments.
That’s why dynamic ratings are always lower than static ratings. A canopy rated at 200kg dynamic and 300kg static isn’t being conservative. It’s reflecting the real forces that act on the roof while driving.
Static load: when the tent is deployed
Static load is the rating that matters when the vehicle is parked and the tent is open with people inside. The vehicle isn’t moving, so there are no acceleration, braking or cornering forces. Just gravity.
For an RTT setup, the static load is usually higher than the dynamic load because it includes occupants. Two adults in a rooftop tent plus the tent structure, mattress and bedding can easily reach 200 to 280kg of static load.
The good news: Most canopies with decent static ratings (250 to 500kg) handle this comfortably when parked. The challenge is always the dynamic rating while driving, not the static rating at camp.
Off road load: why tracks and corrugations change the equation
Off road conditions generate significantly higher forces than sealed roads. Corrugations, washouts and rough tracks amplify the dynamic load on the roof.
Mazda’s own BT-50 accessory ratings show this clearly: the genuine roof platform drops from 70kg on road to 47kg off road, a 33% reduction. The genuine roof racks drop from 90kg to 60kg. That’s not conservative marketing. It reflects the real increase in forces when a loaded vehicle hits rough terrain.
For canopies that don’t publish a specific off road rating, a conservative rule of thumb is to treat the off road capacity as 50 to 60% of the published dynamic rating. A canopy rated at 200kg dynamic becomes roughly 100 to 120kg effective on corrugated roads.
Why you cannot use the static rating as your driving rating
A canopy rated at 300kg static and 100kg dynamic cannot safely carry 300kg while driving. The 300kg figure only applies when the vehicle is parked. While driving, the limit is 100kg and on rough roads it’s even lower.
Using the static rating as a driving guide is one of the most common and most dangerous mistakes in RTT setups. The NTC Load Restraint Guide requires all loads to be properly restrained for the forces experienced during normal driving, including emergency braking and cornering. Static ratings don’t account for these forces.
The 4 ratings you need to check before mounting an RTT
Your BT-50 RTT setup involves multiple components stacked together. Each has its own rating. The real world limit is determined by the weakest link.
Vehicle or roof rating
If the RTT is mounted on the cab roof (rather than the canopy), the vehicle’s own cab roof rating applies. For the BT-50, the genuine Mazda roof racks are rated at 90kg on road and 60kg off road. That’s a tight ceiling for an RTT setup.
Canopy roof rating
If the RTT is mounted on the canopy (the most common setup), the canopy’s roof load rating is the relevant figure. This varies enormously:
- Oz Canopies fibreglass BT-50 canopy: 100kg (roof rails)
- Mazda genuine canopy rail kit: 75kg standard, 150kg with reinforcement
- Oz Canopies heavy duty steel BT-50 canopy: 200kg dynamic, 300kg static
- Premium aluminium touring canopies: 150 to 250kg dynamic
The difference between 75kg and 200kg is the difference between “definitely not RTT ready” and “comfortably supports an RTT with an awning.”
Rack or platform rating
The crossbars, rack or platform mounted on the canopy also have their own rating. Even if the canopy is rated at 200kg, crossbars rated at 100kg limit the setup to 100kg.
Mounting hardware and reinforcement rating
The brackets, clamps and internal reinforcement that connect the rack to the canopy matter. Weak mounting points can fail under the dynamic forces of an RTT, even if the canopy and rack are individually rated high enough. Quality crossbar clamps, proper bolt torque and adequate mounting point spacing are all part of the equation.
The lowest rated part wins
If your canopy is rated at 200kg dynamic, your crossbars are rated at 120kg and your mounting brackets are rated at 100kg, your effective limit is 100kg. Always identify every component in the load path and use the lowest rating as your working limit.
Which BT-50 canopies can support a rooftop tent?
Not all canopies are created equal when it comes to RTT compatibility. Here’s how the main categories stack up.
Basic lifestyle canopies
Standard fibreglass canopies with basic roof rails (75 to 100kg dynamic) are generally not suitable for rooftop tent setups without reinforcement. A folded RTT plus rack weighs 70 to 100kg, which is at or over the limit before adding an awning or any other roof accessory. On corrugated roads where effective loads increase, these setups are clearly over rated.
Our $3,499 fibreglass BT-50 canopy with 100kg roof rails can handle a very light RTT setup (small tent, light rack, no awning) on sealed roads. But for serious RTT touring, especially on unsealed roads, a higher rated canopy is the better choice.
Reinforced canopy roof systems
Mazda’s genuine canopy roof rail kit demonstrates the value of reinforcement. The standard kit is rated at 75kg. Adding the optional reinforcement kit doubles that to 150kg. That’s enough for most RTT setups with moderate accessories on sealed roads, though off road use still requires careful calculation.
Touring specific canopies
Purpose built touring canopies offer the strongest RTT platform. Our heavy duty steel BT-50 canopy is rated at 200kg dynamic and 300kg static, which comfortably supports an RTT, awning, solar panel and recovery boards with margin to spare, even on corrugated roads. At $1,999, it’s also one of the most affordable RTT ready canopies on the market.
ARB’s internally supported canopies offer dynamic ratings between 100kg and 150kg and static ratings between 350kg and 400kg depending on model. These are designed with touring loads in mind.
Premium aluminium expedition canopies (like the Rhinoman CapRax at 250kg dynamic, 500kg static) represent the top end, with ratings that handle any realistic RTT setup with significant margin.
Aftermarket heavy duty canopy rack systems
Some aftermarket rack kits designed specifically for the BT-50 canopy offer higher ratings than the base canopy rails. For example, EGR’s BT-50 Gen3 canopy roof rack kit states a 150kg dynamic load rating. These can upgrade a standard canopy into an RTT capable platform, provided the canopy shell itself can handle the transferred load.
The key takeaway: Don’t ask “can a BT-50 have a rooftop tent?” Ask “can my specific canopy and rack combination support the rooftop tent I want to buy, at the weight I’ll actually load it to, on the roads I’ll actually drive?”
RTT + awning + solar: what changes?
Most RTT owners don’t just mount a tent. They add an awning, a solar panel, recovery boards and various brackets. Each addition changes the maths.
Rooftop tent only
The simplest and lightest RTT setup. Tent (55 to 75kg) plus rack (8 to 20kg) equals roughly 65 to 95kg dynamic. Workable on canopies rated at 120kg+ dynamic. Straightforward to calculate.
Rooftop tent + awning
An awning adds 10 to 20kg and it also creates asymmetric loading (the awning hangs off one side). Total dynamic load: 75 to 115kg. The asymmetric load means the rack and canopy need to handle not just the weight but the leverage effect of the awning pulling on one side, especially during cornering.
Rooftop tent + awning + solar
A fixed solar panel adds 8 to 15kg plus mounting hardware. Total dynamic load with tent, rack, awning and solar: 90 to 140kg. This is where 100kg rated canopies start getting uncomfortable and 150kg+ rated canopies become genuinely necessary.
Bedding and accessories left inside the tent
People leave pillows, doonas, sleeping bags and sheets inside the RTT to save setup time. That’s fine when parked (static load), but it adds 3 to 8kg to the dynamic load while driving. It’s a small number on its own, but on a setup that’s already near the limit, it can push things over.
Why roof weight also affects payload
Every kilo on the roof counts toward the vehicle’s total weight and therefore toward GVM. A 120kg RTT setup is 120kg of payload consumed. On a BT-50 with roughly 1,000kg of payload, that’s 12% gone before you’ve loaded anything inside the canopy.
The BT-50 payload and GVM guide covers how all accessories, including roof mounted gear, interact with your total weight budget.
How to calculate your BT-50 rooftop tent setup weight
Here’s the step by step process. Grab a pen.
Step 1: Find your RTT weight
Check the manufacturer’s spec for the tent’s total weight including the mattress, mounting rails and cover. Don’t use the “body only” weight. You need the complete folded package as it sits on the roof.
Step 2: Add rack or platform weight
Your crossbars, roof rack or platform has its own weight. A pair of heavy duty crossbars weighs 8 to 12kg. An aluminium roof platform weighs 15 to 25kg. This weight counts.
Step 3: Add awning, solar and accessories
Awning: 10 to 20kg. Solar panel: 8 to 15kg. Recovery boards: 6 to 10kg. Brackets and hardware: 2 to 5kg. Add everything that’s bolted to the roof.
Step 4: Compare against dynamic and off road ratings
Add up Steps 1 to 3. That total is your dynamic roof load while driving. Compare it to your canopy’s dynamic roof load rating. For off road use, reduce the canopy’s effective rating by 30 to 40% (or use the published off road rating if available).
Step 5: Check static rating for sleeping setup
Add the occupants’ weight to the total from Steps 1 to 3. Two adults at 75kg each adds 150kg. Compare this total to your canopy’s static roof load rating. Most canopies with 250kg+ static ratings handle this comfortably.
Step 6: Check total vehicle payload
The entire roof setup weight (from Step 1 to 3) counts toward your vehicle’s GVM. Add it to your canopy weight, drawer system, battery, passengers and cargo. Make sure the total stays within your BT-50’s payload.
RTT weight worksheet:
| Component | Your Weight | Typical Range |
| Rooftop tent (folded, complete) | ___kg | 50 to 80kg |
| Roof rack / crossbars / platform | ___kg | 8 to 25kg |
| Awning | ___kg | 10 to 20kg |
| Solar panel + mounting | ___kg | 8 to 15kg |
| Recovery boards + brackets | ___kg | 8 to 14kg |
| Bedding left in tent | ___kg | 3 to 8kg |
| Total dynamic load (driving) | ___kg | 85 to 140kg |
| Add: occupants in tent (parked) | ___kg | 100 to 180kg |
| Total static load (sleeping) | ___kg | 185 to 320kg |
Mounting a rooftop tent on a BT-50 canopy: what to check
Getting the mounting right is just as important as getting the ratings right. A properly rated canopy with a poorly mounted tent is still a safety risk.
Rack spacing. The crossbars or platform mounting points should be spaced wide enough to support the tent’s mounting rails evenly. Most RTT manufacturers specify a minimum and maximum bar spacing. Check the tent’s requirements and confirm your rack matches.
Mounting rail compatibility. The tent’s mounting rails need to match the rack’s channel type. T track, M8 channel and through bolt are the most common. Make sure the tent and rack use compatible mounting systems.
Tent orientation. Most RTTs are designed to open to one specific side (usually the vehicle’s passenger side or rear). Check that the opening direction works with your canopy layout, tailgate access, awning position and ladder placement.
Load distribution. The tent should sit centred across the crossbars, not hanging off one end. Uneven loading creates asymmetric forces that stress the rack, mounting hardware and canopy structure, especially on corrugated roads.
Fastener quality and torque. Use the hardware supplied by the tent and rack manufacturers. Check bolt torque after the first drive and periodically after corrugated roads. Vibration loosens fasteners.
Clearance for canopy doors and windows. Make sure the mounted tent doesn’t prevent the canopy’s lift up windows, gullwing doors or tailgate from opening fully. A tent that blocks a side window means you lose camp access.
Professional installation. If you’re unsure about the canopy rating, rack system or mounting method, have the RTT professionally fitted. A proper install costs a few hundred dollars and ensures everything is mounted, spaced and torqued correctly. Under VSB 14 (the National Code of Practice for Light Vehicle Modifications), any modification that affects the vehicle’s rated capacities needs to meet appropriate standards. A professionally fitted RTT setup gives you peace of mind that the mounting is done right. It’s cheaper than replacing a canopy roof that’s been damaged by a poorly mounted 70kg tent bouncing on corrugations.
RTT setup by travel style: weekend vs touring vs remote trips
Weekend camping setup
Priorities: Light, fast setup, minimal accessories.
A compact hardshell or folding RTT (50 to 60kg) on quality crossbars (8 to 12kg) keeps the dynamic load at 60 to 72kg. No awning needed for one or two nights. Portable solar preferred over fixed to keep roof weight down.
This setup works on canopies rated at 100kg+ dynamic. Our $3,499 fibreglass canopy with 100kg roof rails handles a light weekend RTT setup on sealed roads.
Total roof weight: 60 to 75kg. Well within most mid range canopy ratings.
Touring setup
Priorities: Comfort, awning for shade, solar for extended off grid stays.
A mid size RTT (60 to 75kg) on a proper roof rack or platform (15 to 25kg), plus a 270 degree awning (15 to 20kg) and a 160W solar panel (10 to 14kg). Total dynamic load: 100 to 134kg.
This setup needs a canopy rated at 150kg+ dynamic. Our $1,999 heavy duty steel canopy at 200kg dynamic handles this comfortably with margin for off road use (estimated 120kg off road capacity).
Total roof weight: 100 to 134kg. Requires a purpose rated touring canopy.
Remote and corrugated road setup
Priorities: Conservative roof load, reinforced canopy and rack, careful off road planning.
The same touring setup (100 to 134kg) on corrugated roads needs extra margin. With an estimated off road reduction of 30 to 40%, a canopy rated at 200kg dynamic (effective ~120kg off road) handles it. A canopy rated at 150kg dynamic (effective ~90kg off road) does not.
Post trip habit: After every corrugated road session, check rack bolts, tent mounting fasteners, awning brackets and crossbar clamps. Vibration loosens hardware. A two minute inspection prevents a loose tent on the next stretch.
The BT-50 touring canopy setup guide covers how an RTT fits into a complete touring build with drawers, battery, water and storage.
How rooftop tents affect BT-50 handling, payload and drivability
An RTT doesn’t just sit on the roof. It changes how the BT-50 drives.
Raised centre of gravity. A 70kg tent mounted on top of the canopy raises the vehicle’s centre of gravity significantly. This increases body roll in corners, reduces stability during emergency lane changes and makes the vehicle feel less planted at highway speeds. The higher and heavier the roof load, the more pronounced this effect.
Wind drag. A folded RTT on the roof acts like a sail. It increases fuel consumption noticeably (some owners report 1 to 2L per 100km increase) and makes the vehicle more susceptible to crosswinds. On open highway stretches with strong winds, a roof mounted RTT can make the BT-50 feel noticeably less stable.
Payload reduction. A 120kg RTT setup (tent, rack, awning, solar) is 120kg of payload consumed. On a BT-50 with roughly 1,000kg of factory payload, that’s 12% of your total capacity sitting on the roof. Combined with a canopy, drawers, battery and touring gear inside the tub, an RTT build can easily consume 400 to 600kg of payload before passengers and cargo.
Braking distance. Higher centre of gravity and more total weight both increase braking distance. The NTC Load Restraint Guide principles apply: loads must be secured and the vehicle must be able to stop safely under all conditions, including emergency braking. ANCAP safety testing reinforces that overloaded or poorly balanced vehicles have compromised braking and handling characteristics.
Off road dynamics. A heavy roof load amplifies the effect of corrugations, washouts and uneven terrain. The vehicle’s body moves more on its suspension, increasing stress on every component from the springs to the canopy mounting bolts. This is why off road roof load ratings are lower than on road ratings.
Under the Australian Design Rules (ADRs), the total loaded weight of the vehicle (including everything on the roof) must remain within GVM. The Department of Infrastructure’s vehicle standards framework underpins these requirements.
Common BT-50 rooftop tent mistakes
Only checking the static rating. Seeing “300kg static” and assuming the canopy can carry 300kg while driving. Static is for when you’re parked. Dynamic is for driving and it’s always lower.
Forgetting the rack and platform weight. A 20kg roof platform plus 8kg of mounting hardware is 28kg before the tent even goes on. That counts against the dynamic rating.
Ignoring the off road rating. Mazda’s own accessories show a 33% reduction between on road and off road ratings. If your BT-50 sees unsealed roads (and most touring rigs do), plan for the off road number.
Assuming every canopy supports an RTT. A standard fibreglass canopy with 75 to 100kg roof rails may not safely support a 70kg tent plus a 20kg rack while driving, especially on rough roads. Check the rating before buying the tent.
Adding awning and solar without recalculating. An awning and solar panel add 20 to 35kg to the roof. That can push a setup that was “just within rating” clearly over it.
Leaving heavy bedding inside the tent. A doona, pillows and sheets add 3 to 8kg of dynamic load while driving. On a tight setup, remove bedding before driving and put it back at camp.
Mounting too high or too far back. The higher the RTT sits, the worse the centre of gravity impact. And weight behind the rear axle worsens rear end sag and steering lightness.
Ignoring payload. The RTT setup is part of the vehicle’s total weight. It doesn’t sit in some separate “roof” category. Every kilo on the roof reduces the payload available for passengers, cargo and towball download.
Not checking fasteners after corrugations. Vibration loosens mounting bolts, crossbar clamps and bracket hardware. Check everything after rough roads.
Choosing the tent before choosing the canopy and rack. The canopy and rack determine what tent you can safely carry. Buy those first, confirm the ratings, then choose a tent that fits within the limits. Not the other way around.
Rooftop tent vs swag, ground tent or trailer: is an RTT right for your BT-50?
An RTT is a brilliant accessory for the right owner. But it’s not the right choice for everyone.
RTT benefits: Fast setup (usually under 2 minutes), off ground sleeping (no rocks, no snakes, no puddles), comfortable mattress built in, great for bush camping where ground is uneven or wet and it looks the part.
RTT downsides: 50 to 80kg of permanent roof weight (payload and handling impact), raises the vehicle height (affects garages, car parks and low branches), increases fuel consumption, costs $1,500 to $4,000+ for the tent alone and requires a canopy and rack rated for the load.
When a ground tent or swag is smarter: If you camp less than once a month, if payload is already tight, if the canopy isn’t RTT rated or if you prefer to keep the roof light for better handling and fuel economy. A quality swag weighs 8 to 12kg and stores inside the canopy. That’s 50 to 70kg less than an RTT setup on the roof.
When a camper trailer changes the equation: If you tow a camper trailer with sleeping built in, you don’t need an RTT on the BT-50. The trailer handles sleeping and the canopy handles fridge, storage and daily gear. This keeps the ute’s roof light and preserves payload for the towing interaction. The BT-50 towing with a canopy guide covers how canopy weight and towing interact.
The honest take: An RTT is worth it for owners who camp regularly (most weekends) and want the fastest, most convenient setup. For occasional campers, a swag or ground tent does the same job at a fraction of the weight, cost and roof load pressure.
What we recommend at Oz Canopies & 4×4
We help BT-50 owners plan RTT compatible canopy builds regularly and the advice is always the same: choose the canopy and rack first, confirm the ratings, then buy the tent.
If you’re planning an RTT setup: Our $1,999 heavy duty steel BT-50 canopy with 200kg dynamic and 300kg static roof load is the most affordable RTT ready canopy we offer. It handles a rooftop tent, awning and solar panel with genuine margin, even on corrugated roads. Pair it with our heavy duty crossbars ($449, rated to 300kg) and you’ve got a rock solid RTT platform for under $2,500.
If you want a lighter canopy with RTT capability: A premium aluminium touring canopy with 150kg+ dynamic rating is the step up. More expensive but lighter, which preserves more payload for the rest of the build.
If you’re not sure your current canopy is RTT ready: Tell us your canopy brand, model and roof rating. We’ll help you work out whether it can safely carry the tent you’re looking at or whether a canopy upgrade is the smarter move before investing $2,000+ in a tent.
With 700+ five star Google reviews, we’d rather help you get the canopy right first than sell you an RTT setup that overloads the roof.
Call us on 02 9627 8666, text 0440 130 098 or visit our showroom at 20 Walker St, South Windsor to talk through your RTT plans.
FAQs
Can I put a rooftop tent on a BT-50 canopy?
What roof rating do I need for a BT-50 rooftop tent?
What is the difference between dynamic and static roof load?
Does an RTT count toward payload?
Can I mount an RTT on a fibreglass canopy?
Do I need a reinforced canopy for a rooftop tent?
Can I run an awning and solar panel with an RTT?
What happens to roof load off road?
Should I mount the RTT on the cab roof or canopy?
Is a rooftop tent worth it for weekend camping?
Quick RTT decision guide: is your BT-50 ready?
Step 1: What’s your canopy’s dynamic roof load rating?
- Under 100kg → not RTT suitable without reinforcement or upgrade
- 100 to 150kg → light RTT only, sealed roads mainly
- 150 to 200kg → most RTT setups with awning and solar
- 200kg+ → full RTT touring setup with off road margin
Step 2: Add up everything going on the roof.
- Tent + rack + awning + solar + accessories = total dynamic load
- Compare to your canopy’s dynamic rating (use off road rating for unsealed roads)
Step 3: Check the static rating.
- Total dynamic load + occupants in tent = static load when parked
- Compare to your canopy’s static rating
Step 4: Check your total vehicle payload.
- Roof load + canopy + drawers + battery + passengers + cargo = total payload used
- Compare to your BT-50’s GVM
If all four checks pass, your BT-50 is RTT ready. If any one fails, address it before buying the tent.
Want help working out whether your BT-50 canopy can handle a rooftop tent? Tell us your canopy brand, your planned tent and what else is going on the roof. We’ll check the numbers and make sure the setup is safe and realistic.
Call 02 9627 8666, text 0440 130 098 or drop into Oz Canopies & 4×4 at 20 Walker St, South Windsor.